Joab EcoDrive Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 73

background image

59

Safety Warnings

The EcoDrive Hook-Lift has a number of safety labels attached to it, as shown below. It is import-
ant to read and adhere to these warnings. Failure to do so can lead to serious injury or damage
to equipment.

Make sure that the labels are in good condition. If necessary, new safety labels can be ordered
from JOAB.

Safe Working Distance

Make sure that there are no unauthorised persons in close prox-
imity of the EcoDrive Hook-Lift's working area. The risk zone is 8
metres in all directions of the EcoDrive Hook-Lift and body.

Working on the Hook-Lift

Never work under a hook-lift without the use of the tip-supports.
Make sure that the body is removed from the hook-lift and that
the tip-supports are mounted correctly so that they support the
hook-lift, before carrying out any work.

Refer also to

"Working on the Hook-Lift", on page 56

Park the Hook-Lift before driving the Vehicle

Make sure the hook lift is parked before driving the vehicle. Fail-
ure to do so can lead to serious injury or damage. There is a ser-
ious risk that the hook will make contact with the environment if it
is not parked.

Risk of Slipping

Be aware when operating the hook-lift that there may be a risk of slipping, that
could lead to injury.

Suspended Loads

Do not stand or walk underneath a suspended load. If a suspended load
breaks free it can lead to serious injury or death.

EcoDrive manual: 13300 Edition 1 | 2019-01-31

«
...
65
66
67
68
69
...
»

Содержание EcoDrive










































































Отзывы:

Нет отзывов

Похожие инструкции для EcoDrive

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 16

Бренд: M-system Страницы: 10

Бренд: Carel Страницы: 2

Millermatic 212

Бренд: Miller Electric Страницы: 44

Бренд: Estun Страницы: 41

PRECISION TIG 185

Бренд: Lincoln Electric Страницы: 104

Бренд: Gabarron Страницы: 16

Бренд: National Instruments Страницы: 77

Бренд: ICP DAS USA Страницы: 8

Бренд: HEEVE Страницы: 16

Бренд: ReadyLift Страницы: 20

Бренд: Pro-Lift Страницы: 20

Бренд: Major Страницы: 44

Бренд: APS Resource Страницы: 28

HandyPlasma 250

Бренд: ESAB Страницы: 48

RFID-USB-DESK Reader

Бренд: inveo Страницы: 11

Бренд: Chrosziel Страницы: 2

Бренд: Peak Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды