Joab EcoDrive Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 73

background image

31

Distributing a Load on a Body

The operator of the hook-lift is responsible for handling it. Care must be taken to
avoid injury or damage. Before operating the hook-lift make sure that you have read
and are fully aware of the warnings in this manual and on the hook-lift.

Before lifting a body with a load, make sure
that:

l

The load does not exceed the hook-lift’s
maximum lifting capacity.

l

The load is evenly distributed.

l

The lifting is done on a level ground.

l

The body’s support rollers rotate.

If a load is unevenly distributed, the lifting capa-
city can be reduced. For example, if the load is
positioned at the front of the vehicle, the lifting
capacity can be reduced by up to 40%.

Another important condition to consider is how
long the body is. The length of the body and the
load on it affect the lifting capability of the hook-
lift.

A short overhang causes an abnormal load. A
correctly designed body for your chassis will dis-
tribute the load correctly.

EcoDrive manual: 13300 Edition 1 | 2019-01-31

«
...
37
38
39
40
41
...
»

Содержание EcoDrive










































































Отзывы:

Нет отзывов

Похожие инструкции для EcoDrive

Бренд: Happ Страницы: 49

Бренд: National Instruments Страницы: 20

Бренд: National Instruments Страницы: 6

Бренд: National Instruments Страницы: 30

Бренд: National Instruments Страницы: 7

Бренд: National Instruments Страницы: 37

Бренд: National Instruments Страницы: 8

Бренд: M-system Страницы: 5

R1000 series E20

Бренд: Roland Страницы: 156

Бренд: Unimig Страницы: 14

Бренд: WAGO Страницы: 20

Бренд: H&H Страницы: 23

Бренд: Buffalo Страницы: 2

HRU-WALL-RC Series

Бренд: Nalnor Страницы: 32

Бренд: MAGNAWELD Страницы: 18

Бренд: ICP DAS USA Страницы: 82

Бренд: Migomag Страницы: 43

Бренд: WinSystems Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды