Joab EcoDrive VL10U Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 57

background image

49

Safety Warnings

The skip-loader has a number of safety labels attached to it, as shown below. It is important to
read and adhere to these warnings. Failure to do so can lead to serious injury or damage to
equipment.

Make sure that the labels are in good condition. If necessary, new safety labels can be ordered
from JOAB.

Safe Working Distance

Make sure that there are no authorized persons in close prox-
imity of the vehicle's working area. The risk zone is 8 meters in
all directions of the vehicle.

Skip-Loader's working Area

The area directly behind the skip-loader must be kept free from
obstructions and persons. Make sure that there is a distance of
10 m between the back of the vehicle and any obstructions or
persons. Failure to do so can lead to serious injury or damage.

Risk of Slipping

Be aware when operating the skip-loader, there may be a risk of slipping, that
could lead to injury.

Suspended Loads

Do not stand or walk underneath a suspended load. If a suspended load
breaks free it can lead to serious injury or death.

Risk of being Trapped

Be aware that there is a serious risk of becoming trapped when operating the
equipment. Always verify that there is no risk of anyone becoming trapped or
injured before operating the equipment.

EcoDrive VL10-VL18 manual: 1021046 Edition 2 | 2022-05-02

«
...
53
54
55
56
57
»

Содержание EcoDrive VL10U


























































Отзывы:

Нет отзывов

Похожие инструкции для EcoDrive VL10U

Бренд: Patton Страницы: 4

Бренд: Mark Climate Страницы: 60

7.4VOLT HEATED GLOVES

Бренд: Mobile Warming Страницы: 6

Бренд: CAME Страницы: 28

Бренд: Logic Страницы: 3

Бренд: Keurig Страницы: 6

Бренд: Ravaglioli Страницы: 88

Aristo RoboFeed 30-4

Бренд: ESAB Страницы: 34

ENERGY BOX - TO 1.400

Бренд: AirTechnic Страницы: 20

Бренд: HALDER Страницы: 2

ControlLogix 1756-CNB

Бренд: Allen-Bradley Страницы: 36

Бренд: iWeld Страницы: 10

Бренд: ROTOTILT Страницы: 17

Бренд: Measurement Computing Страницы: 50

Бренд: Net.Do Страницы: 35

Бренд: WARPP Страницы: 11

Бренд: Lincoln Electric Страницы: 35

Бренд: 2VV Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды