Joab EcoDrive VL10U Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 57

background image

5.

Verify that all lighting and other electrical
equipment functions correctly.

6.

Finish by inspecting the hydraulic pump.

If any damage is found, contact your JOAB workshop
immediately.

Washing the Skip-Loader

Newly lacquered surfaces must be cleaned using detergent and a sponge only. Do not use a
high pressure washer. A high pressure washer should only be used after at least three weeks
following treatment of surfaces.

Detergents contain acids. Make sure that the cleaning fluid used to clean surfaces contains
less than 9pH. The maximum temperature of the cleaning fluid must not exceed 50 °C above
the ambient temperature. After washing, make sure to rinse all surfaces thoroughly.

Cleaning the skip-loader with a high pressure washer entails risks. All electrical components,
even enclosed, are sensitive to water under high pressure.

When using a high pressure washer, make sure to hold the nozzle at least 45 cm from all
lacquered surfaces. Use a standard nozzle only, do not use a turbo nozzle.

Always apply fresh grease around lubrication points after washing. For more information
regarding the skip-loaders lubrication points, refer to below.

40

Service and Maintenance | Washing the Skip-Loader

EcoDrive VL10-VL18 manual: 1021046 Edition 2 | 2022-05-02

«
...
44
45
46
47
48
...
»

Содержание EcoDrive VL10U


























































Отзывы:

Нет отзывов

Похожие инструкции для EcoDrive VL10U

Бренд: Vestil Страницы: 11

Бренд: ShoreStation Страницы: 19

Heat Control System

Бренд: ORTAL Страницы: 20

Бренд: WattMaster Страницы: 104

Бренд: EWM Страницы: 33

Бренд: Bame Страницы: 12

iNELS Air AirIM-100S

Бренд: Elko Страницы: 8

Бренд: BUCKINGHAM MFG Страницы: 7

Бренд: HALDER Страницы: 2

ControlLogix 1756-CNB

Бренд: Allen-Bradley Страницы: 36

Бренд: American Panel Страницы: 18

Бренд: ICP DAS USA Страницы: 8

Бренд: Xycom Страницы: 104

Hydraguide HGA Series

Бренд: Parker Страницы: 30

Micro Mag 302 MFK

Бренд: Weco Страницы: 34

Бренд: Raven Страницы: 59

Бренд: morse Страницы: 6

Бренд: Philips Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды