background image

Hardware Used

AA

BB

1

x 4

x 4

M

AA

BB

Bolt M6x10

M6  nut

14

13

 

 

 

 

  

 

 

 

 

 

 

 

 

 

Assembly Procedure

 

2

Hardware Used

CC

x 8

screw M5x10

HH

x 8

Screw 3/16” 

3

HH

CC

D

1.Assemble the wheel assembly (M) to the   
bottom plate (N) using 4pcs bolt M6x10 
(AA) and 4pcs M6 nut (BB).

Hardware Used

CC

 x 8

screw M5x10

2-1. Unscrew the ignition, load small battery, 
tighten the ignition.

2-2. Insert the pins of the bottom plate (N) to the 
holes of lower support (L), press to secure the 
pins. using 4pcs screw M5x10 to secure the 
bottom plate and lower support.
Insert the pins of the control box assy (K) to the 
holes of lower support (L), press to secure the 
pins. using 4pcs screw M5x10 to secure the lower 
support and control box assy.

3. Insert upper support (D) to lower support 
(L) using 8pcs screw M5x10.
Assemble top plate assy (B) to upper 
support (D) using 8pcs screw 3/16”.

L

K

CC

CC

N

 

Hardware Used

4

4

.

Assemble the reflector (A) onto the top
plate assy (B).
Screw the 3pcs stud (DD) on the top plate
assy (B), put 3pcs flat washer (FF) onto the
top of stud (DD), then put the reflector on
the the stud (DD), secure them with 3pcs
flat washer (FF) and 3pcs wing nut (EE).

EE

FF

FF

DD

x 3

x 3

x 6

EE

Wing nut

Stud

DD

FF

Flat washer

ATTENTION:

Ensure control box and front panel are on
opposite side to wheels.

NN

Содержание JMC-OSPH-SS











Отзывы: