JLG GRADALL 544D-10 Скачать руководство пользователя страница 98

Страница: 98 / 142

Section 5 - Attachments

5-36

31200172

Bucket

Description

P/N

Bucket, 60 in - 0.75 yd

(Before S/N 0160037689)....... 90455049

Bucket, 72 in - 1.0 yd

(S/N 0160037689 & After) .... 1001100822

Bucket, 74 in - 1.25 yd

(Before S/N 0160037689)....... 90555020

Bucket, 74 in - 2.0 yd

(Before S/N 0160037689)......... 90453039

Bucket, 96 in - 1.5 yd

(S/N 0160037689 & After) .... 1001100823

Bucket, 102 in - 2.0 yd

(S/N 0160037689 & After) .. 1001100824

Concrete Hopper - 0.75 yd

(Before S/N 0160037689) ............................................. 91123115

Use Appropriate Bucket Capacity Chart

To determine maximum capacity, refer to

“Telehandler/Attachment/Fork Capacity”

page 5-3.

The joystick (

) controls lift/lower and extend/retract movement of the boom.

The tilt lever (

) controls bucket tilt.

• Move lever back to tilt up.

• Move lever forward to tilt down.

Installation Procedure:

• Refer to

“Attachment Installation”

on page 5-11.

OZ0730

OX0251

2-FRONT

Содержание GRADALL 544D-10















































































































































Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Бренды по названию

Популярные бренды

JLG GRADALL 544D-10, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Бренды по названию

Популярные бренды