JLG GRADALL 544D-10 Скачать руководство пользователя

Страница: 78 / 142

Section 5 - Attachments

5-16

31200172

5.7

ATTACHMENT OPERATION

• Capacities and range limits for the telehandler change depending on the

attachment in use.

• Separate attachment instructions must be kept in manual holder in cab with this

Operation & Safety Manual. An additional copy must be kept with the attachment
if it is equipped with a manual holder.

• Operations described within this section reference right hand attachment tilt and

left hand auxiliary hydraulics controls. Refer to pages 3-9 or 3-1 1 if equipped with
a different configuration.

NOTICE

EQUIPMENT DAMAGE.

Some attachments may contact the front tires or

machine structure when the boom is retracted and the attachment is rotated.
Improper use of attachment may result in attachment or machine structural
damage.

NOTICE

EQUIPMENT DAMAGE.

Avoid contact with any structure or object when lifting a

load. Maintain clearance around boom structure and load. Failure to maintain
clearance may result in attachment or machine structural damage.

Содержание GRADALL 544D-10















































































































































Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды

JLG GRADALL 544D-10, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды