JLG GRADALL 544D-10 Скачать руководство пользователя

Страница: 44 / 142

Section 3 - Controls and Indicators

3-10

31200172

Outrigger Levers

The rear levers (

1 & 2

) control the outriggers.

• The left lever controls the left outrigger and the right lever controls the right

outrigger.

• Push levers forward to lower outriggers; push levers back to raise outriggers.

• Use outriggers to increase stability and/or load capacity and in leveling the

telehandler. Study capacity charts to determine maximum load capacities, with
and without outriggers.

WARNING

TIP OVER HAZARD.

Outriggers increase stability and load capacity only if they

are used properly. Using outriggers on soft surfaces could cause telehandler to
tip over. Always ensure surface can support telehandler and load.

OX0492

Содержание GRADALL 544D-10















































































































































Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды

JLG GRADALL 544D-10, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды