JLG GRADALL 544D-10 Скачать руководство пользователя

Страница: 125 / 142

Section 7 - Lubrication and Maintenance

7-17

31200172

Hydraulic Return Filter

A. Hydraulic Return Filter Indicator Check

1. Apply park brake, shift transmission to "Neutral" and lower forks or attachment

to horizontal position.

2. Check hydraulic return filter indicator with engine at normal operating

temperature.

3. Have an assistant open the tank cover.

4. With the engine at full throttle and the assistant observing the indicator (

)

located on the hydraulic return filter (

), extend and retract the boom 10 to 12 ft

(3,0 to 3,7 m). The bar gauge should be within the green area.

5. Replace filter before the gauge reaches the red area on the indicator. If it

reaches the red area, the filter is too dirty and hydraulic oil is bypassing the
filter.

6. Close and secure the tank cover.

OW0970

OW1060

OX0170

Содержание GRADALL 544D-10















































































































































Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды

JLG GRADALL 544D-10, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды