JLG GRADALL 544D-10 страница 121 Скачать руководство пользователя

Страница: 121 / 142

Section 7 - Lubrication and Maintenance

7-13

31200172

Hydraulic Oil

A. Hydraulic Oil Level Check

1. Be sure all cylinders are fully retracted and machine is level.

2. Perform

“Shut-Down Procedure”

on page 4-4.

3. Check level of hydraulic oil at the sight gauge (

) on the hydraulic tank (

). The

oil level should be visible in the gauge window.

4. If hydraulic oil is low, open the tank cover and remove oil fill cap (

) from filler

neck. Add hydraulic fluid to bring oil up to the upper mark on the sight gauge.

5. Replace hydraulic oil fill cap.

6. Close and secure the tank cover.

OW0970

OW1030

OX0180

2-FRONT

Содержание GRADALL 544D-10















































































































































Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды

JLG GRADALL 544D-10, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды