JLG GRADALL 544D-10 страница 103 Скачать руководство пользователя

Страница: 103 / 142

Section 5 - Attachments

5-41

31200172

Personnel Work Platform (Before S/N 0160037689)

The operator and personnel in platform must read and understand the
separate personnel work platform manual prior to installing and using a
platform.

Preparation and Setup

1. Check to ensure the personnel platform is securely attached at the quick switch

or is securely attached to the forks and/or carriage if using fork mounted
personnel work platform. Follow installation procedure on page 5-11 for JLG
quick switch mounted personnel work platforms.

2. Ensure the telehandler is on a firm surface and is level.

3. Engage the park brake. Blocking the wheels is also recommended.

4. Level the platform, both side to side (frame level) and front to back

(attachment tilt).

5. Keep area under the platform free from personnel.

6. When personnel are on platform, the operator must remain seated in cab with

personnel in direct line of sight.

DO NOT

lift or carry persons in the bucket or on forks.

WARNING

FALL HAZARD.

Never tilt the platform forward, rearward, or level the machine

when the platform is occupied.

Содержание GRADALL 544D-10















































































































































Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды

JLG GRADALL 544D-10, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды