JLG GRADALL 544D-10 страница 100 Скачать руководство пользователя

Страница: 100 / 142

Section 5 - Attachments

5-38

31200172

Grapple Bucket (S/N 0160037689 & After)

Description

P/N

Bucket, Grapple, 96 in - 1.75 yd

.................................... 0930020

Use Grapple Bucket Capacity Chart

To determine maximum capacity, refer to

“Telehandler/Attachment/Fork Capacity”

page 5-3.

The joystick (

) controls lift/lower and extend/retract movement of the boom.

The tilt lever (

) controls grapple bucket tilt.

• Move lever back to tilt up.

• Move lever forward to tilt down.

To open/close grapple:

The auxiliary hydraulic lever (

) controls the open/close movement of the grapple.

• Move lever up to close grapple.

• Move lever down to open grapple.

Installation Procedure:

• Refer to

“Attachment Installation”

on page 5-11.

OZ1450

OX0760

2-FRONT

Содержание GRADALL 544D-10















































































































































Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды

JLG GRADALL 544D-10, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды