JLG G10-55A Скачать руководство пользователя

Страница: 64 / 160

Section 4 - Operation

4-4

31200745

Normal Engine Operation

• Observe instrument panel frequently to be sure all systems are functioning

properly.

•

Be alert for unusual noises or vibration.

When an unusual condition is

noticed, park machine in safe position and perform shut-down procedure. Report
condition to your supervisor or maintenance personnel.

•

Avoid prolonged idling.

If the engine is not being used, turn it off.

Shut-Down Procedure

When parking the telehandler, park in a safe location on flat level ground and away
from other equipment and/or traffic lanes.

1. Apply the park brake.

2. Shift the transmission to “Neutral.”

3. Lower forks or attachment to the ground.

4. Operate engine at low idle for 3 to 5 minutes.

DO NOT over rev engine.

5. Shut off engine and remove ignition key.

6. Exit telehandler properly.

7. Block wheels (if necessary).

Содержание G10-55A

































































































































































Результаты поиска

Содержание G10-55A

Отзывы:

Похожие инструкции для G10-55A

Бренды по названию

Популярные бренды

JLG G10-55A, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание G10-55A

Отзывы:

Похожие инструкции для G10-55A

Бренды по названию

Популярные бренды