JLG G10-55A Скачать руководство пользователя

Страница: 53 / 160

Section 3 - Controls and Indicators

3-13

31200745

Outrigger Joysticks

The rear joysticks (

) control the outriggers.

• Left joystick controls left outrigger and right joystick controls right outrigger.

• Push joysticks forward to lower outriggers; push joysticks back to raise outriggers.

• Use outriggers to increase stability and/or load capacity and in leveling the

telehandler. Study capacity charts to determine maximum load capacities, with
and without outriggers.

WARNING

TIP OVER HAZARD.

Outriggers increase stability and load capacity only if they

are used properly. Using outriggers on soft surfaces could cause telehandler to
tip over. Always ensure surface can support telehandler and load.

OY2

Содержание G10-55A

































































































































































Результаты поиска

Содержание G10-55A

Отзывы:

Похожие инструкции для G10-55A

Бренды по названию

Популярные бренды

JLG G10-55A, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание G10-55A

Отзывы:

Похожие инструкции для G10-55A

Бренды по названию

Популярные бренды