manualshive.com logo in svg

JLG G10-55A, Инструкция по эксплуатации и безопасности

Поделиться
Скачать
JLG G10-55A Скачать руководство пользователя страница 44

Section 3 - Controls and Indicators

3-4

31200745

Dash Controls and Indicators

1.

Transmission Temperature Indicator: Illuminates red when transmission 
temperature is too high. Immediately bring machine to a stop, retract and lower 
boom and stop the engine. Determine cause and correct before continued use.

2.

Engine Pre-Heat Indicator: Illuminates yellow with ignition key in the “RUN” 
position. Indicator goes out when start temperature is reached.

3.

Steer Select Switch: Three positions: 4-wheel circle steer, 4-wheel crab steer 
and 2-wheel steer. See page 3-16 for details.

4.

Park Brake Switch: See page 3-7 for details.

5.

Horn Button: Depress button to sound horn.

6.

Auxiliary Electrics Switches (if equipped): Enables functions of attachments that 
require auxiliary electrics. See Section 5 - Attachments for approved 
attachments and control instructions.

7.

Quick Switch Switch (if equipped): Use in conjunction with the auxiliary 
hydraulic joystick to hydraulically lock or unlock an attachment. See 

“Hydraulic 

Quick Switch”

 on page 5-11.

8.

Engine Warning Indicator: Illuminates red when the engine is a critical state. 
Immediately bring machine to a stop, retract and lower boom and stop the 
engine. Determine cause and correct before continued use. Engine may derate.

9.

Check Engine Indicator: Illuminates orange when maintenance is required. See 
Service Manual for details.

10.

3-in-1 Gauge and Display:

a. Engine Coolant Temperature Gauge

b. Engine Oil Pressure Gauge

c. Fuel Gauge

d. Display - Displays engine operating hours, battery voltage and engine 

rpm. Engine fault codes displayed when detected. See Service Manual 
for details.

OY

319

0

1

3

6

9

1

0

8

4

5

2

7

Содержание G10-55A

































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды