JLG G10-55A Скачать руководство пользователя страница 38

Страница: 38 / 160

Section 2 - Pre-Operation and Inspection

2-12

31200745

2.4

WARM-UP AND OPERATIONAL CHECKS

Warm-Up Check

During warm-up period, check:

1. Heater, defroster and windshield wiper (if equipped).

2. Check all lighting systems (if equipped) for proper operation.

3. Voltmeter should show 13.5 to 14 volts.

4. Adjust mirror(s) for maximum visibility.

Operational Check

When engine warms, perform an operational check:

1. Service brake and parking brake operation.

2. Forward and reverse travel.

3. Each gear.

4. Steering in both directions with engine at low idle (steering lock to lock will not

be reached). Check in each steering mode.

5. Horn and back-up alarm. Must be audible from inside operators cab with engine

running.

6. All joystick functions - operate smoothly and correctly.

7. Perform any additional checks described in Section 8.

WARNING

CUT/CRUSH/BURN HAZARD.

Keep engine cover closed while engine is

running except when checking transmission oil level and hydraulic filter condition
indicator.

Содержание G10-55A

































































































































































Результаты поиска

Содержание G10-55A

Отзывы:

Бренды по названию

Популярные бренды

JLG G10-55A, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание G10-55A

Отзывы:

Бренды по названию

Популярные бренды