JLG G10-43A, Инструкция по эксплуатации и безопасности

Страница: 27 / 170

Section 2 - Pre-Operation and Inspection
2-3 31200150
2.2 SAFETY DECALS
Ensure all DANGER, WARNING, CAUTION and instructional decals and proper
capacity charts are legible and in place. Clean and replace as required.
ANSI
Before S/N 0160040121
O Y 0483
9 1 5 0310 8
9150-3108 REV -
M O V I N G PA RT S c o u l d
c r u s h c a u s i n g d e a t h
o r s e r i o u s i n j u r y.
K e e p c l e a r o f w h e e l s a n d
m o v i n g p a r t s w h i l e e n g i n e
i s r u n n i n g .
9 1 5 0310 8
9150-3108 REV -
M O V I N G PA RT S c o u l d
c r u s h c a u s i n g d e a t h
o r s e r i o u s i n j u r y.
K e e p c l e a r o f w h e e l s a n d
m o v i n g p a r t s w h i l e e n g i n e
i s r u n n i n g .
1 7 01 5 0 5
( B EFO RE
S/ N 01 6 001 6 12 9 )
1 7 0 588 1
9 1 5 0310 9
9150-3109 REV -
N O R I D E R S . R i d e r s c o u l d FA L L O F F
m a c h i n e c a u s i n g d e a t h o r s e r i o u s i n j u r y.
DO NOT use Ether or
other high energy
starting aids.
Engine equipped with
Pre-heating system.
ENGINE EXPLOSION
could result in death
or serious injury.
1706300C
1 7 0 6 300
( P ER K IN S ENGINE
ON LY )
9 1 5 13201
(IF E Q UI PP ED WIT H
TI L T ON J O YS TIC K )
9151-3201 REV. (-)
9 1 5 030 98
9150-3098 REV. A
For safe operation of machine, and to minimize risk of
s e r i o u s i n j u r y, R E A D A N D O B S E RV E t h e f o l l o w i n g :
6. Keep others away from machine when operating. Do not
allow others to stand under boom or load. Always look in
direction of travel.
7. Use extreme care when handling long, high or wide loads.
Do not handle unstable or loosely stacked loads.
8. Forks must be centered under load, and spaced apart as far
as possible.
9. Level machine before lifting any load above 4 feet (1.2m).
10. Improper use of machine could result in machine tipping
over. If machine starts to tip over, do not leave operator's
seat. Lean away from tip, and brace yourself.
11. Keep mirror(s) clean and properly adjusted. Objects in
mirror(s) are closer than they appear.
5. On inclines, travel with load up-grade.
1. Only trained and authorized personnel may operate this
machine.
2. Before operating, read and understand all capacity charts,
operator manual and safety manuals.
3. Operator must be seated with seat belt fastened. Assure all
controls are in neutral before ignition switch is turned on.
4. Do not travel with boom raised. When traveling, fully
retract boom and place forks in carry position, which is
approximately 4 feet (1.2 m) above ground. Tilt carriage
back slightly to cradle load. Use extreme caution when
turning.
9 1 5 03110
CONTACTING ELECTRIC POWER
L I N E S w i l l r e s u l t i n d e a t h
o r s e r i o u s i n j u r y.
D o n o t p l a c e m a c h i n e o r l o a d
w i t h i n 1 0 f e e t ( 3 m ) o f e l e c t r i c
9150-3110 REV - A
p o w e r l i n e s .
10 FT.
(3 M)
9 1 5 1320 8
9151-3208 REV -
When lifting personnel, USE ONLY a Gradall manufactured
personnel work platform, with proper personnel work
platform CAPACITY CHART DISPLAYED in cab.
READ AND UNDERSTAND personnel work platform Owner/Operator
manual before lifting personnel.
DO NOT DRIVE machine from cab when personnel are on platform.
All personnel on platform must WEAR A FULL BODY HARNESS,
with lanyard attached to a designated anchorage point.
When personnel are on platform, the OPERATOR MUST REMAIN
SEATED in cab with personnel in direct line of sight.
OPERATE CONTROLS CAUTIOUSLY and lightly when lifting or
positioning personnel.
Failure to comply could result in death or serious injury.
9 1 5 03102
9150-3102 REV. -
9 1 5 131 9 2
(G 9- 43A)
1001112 77 3
(G10 - 43A)
Diesel Engine
SERVICE INTERVALS
LUBRICATION AND MAINTENANCE
MATERIAL HANDLER
9151-3192 REV(B)
U s e t h i s c h a r t i n c o n j u n c t i o n w i t h t h e " L u b r i c a t i o n & M a i n t e n a n c e " a n d " R e c o m m e n d e d
L u b r i c a n t s & C a p a c i t i e s " s e c t i o n s o f t h e O w n e r / O p e r a t o r M a n u a l .
S e r v i c e i n t e r v a l s m a y n e e d t o b e m o r e f r e q u e n t t h a n t h o s e s h o w n d e p e n d i n g u p o n
a p p l i c a t i o n s e v e r i t y. C o n s u l t y o u r G r a d a l l d e a l e r f o r r e c o m m e n d a t i o n s .
I t i s r e c o m m e n d e d t h a t e n g i n e o i l a n d f i l t e r, t r a n s m i s s i o n l u b r i c a n t a n d f i l t e r,
t r a n s f e r c a s e l u b r i c a n t a n d a x l e l u b r i c a n t b e c h a n g e d a f t e r f i r s t 1 0 0 h o u r s o n
n e w, o r r e b u i l t
LUBRICANT TYPE
OR
SPECIFICATION
Air Cleaner Element
Fuel Filter
Engine Oil Filter
Engine Oil
Coolant
Diesel Fuel
YEARLY
OR
1500 HRS
6 MO.
OR
1000 HRS
3 MO.
OR
500 HRS
EVERY 5
WKS OR
250 HRS
WEEKLY
OR
50 HRS
DAILY
OR
10 HRS
Transmission
Lubricant
Filter
Transfer Case
Lubricant
Center Section
Axle Lubricant
Planetary Hubs
Filter
Lubricant
Hydraulic System
Breather/Filter
Grease Fittings
Axles (6 Pts. Ea.)
Boom Head Pivot (2 Pts.)
Boom Pivot (2 Pts.)
Extend Chain Sheave (1 Pt.)
Drive Shafts (1 Pt. Ea.)
Cylinder Pins(13 Pts.)
Quick Switch Pin (1 Pt.)
Retract Chain Sheave (1 Pt.)
Boom
Front Bottom Bearing Pads
All Other Bearing Pads
Extend/Retract Chains
Options And Attachments
Stabilizer Cylinder (3 Pts.)
Attachment Pivots And Pins
Tires
13.00-24 12 Ply
13.00R24 Radial
15.5-25 12 Ply
Lug Nut Torque Torque
Check
Check
Check
Check
Check
Check
Check
Check
Check
Check
Check
Check
Check
Check
Grease
Grease
Grease
Grease
Grease
Grease
Grease
Grease
Grease
Grease
Grease
Grease
Change
Change
Change
Change
Change
Change
Change
Change
Change
Change
Change
Change
SAE 15W-40 CE Oil
Etheylene Glycol
No. 2 Diesel Fuel
Mobil 424
Mobil 424
Mobil 424
Mobil 424
Mobil 424
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
See Manual
65 PSI (448 kPa)
70 PSI (483 kPa)
58 PSI (400 kPa)
350-400 Lb-Ft (475-540 Nm)
Fill
VIEW OF DECALS LOCATED INSIDE
CAB ON RIGHT HAND WALL