JLG 680S Скачать руководство пользователя страница 54

Страница: 54 / 530

SECTION 3 - CHASSIS & TURNTABLE

3-2

3121234

Tighten nuts in the following sequence:

The tightening of the nuts should be done in stages. Fol-
lowing the recommended sequence, tighten nuts per
wheel torque chart.

Wheel nuts should be torqued after first 50 hours of
operation and after each wheel removal. Check torque
every 3 months or 150 hours of operation.

3.2

LOCKOUT CYLINDER BLEEDING

ENSURE PLATFORM IS FULLY LOWERED AND BOOM IS CENTERED OVER REAR
AXLE PRIOR TO BEGINNING BLEEDING PROCEDURE.

ENSURE MACHINE IS ON A LEVEL SURFACE AND REAR WHEELS ARE BLOCKED,
BRAKE WIRE IS DISCONNECTED.

Make sure machine is on a level surface.

Center boom over rear axle to make sure the cam valve
in the rotary coupling is depressed.

Place chocks under the tires to ensure the machine does
not move. Remove the coil from the valve stem.

Use suitable containers to catch any excess hydraulic
fluid. Place the containers under each lockout cylinder.

Open one bleeder screws at a time.

Start the engine, position drive control lever on the main
hydraulic pump forward or reverse.

Close bleeder screws when all air is dissipated (bled).

Reconnect the brake solenoid and remove the wheel
chocks.

Perform oscillating axle lockout test.

10.

If necessary, repeat steps 1 through 7.

Table 3-1. Wheel Torque Chart

TORQUE SEQUENCE

1st Stage

2nd Stage

3rd Stage

70 ft. lbs.

(95 Nm)

170 ft. lbs.

(225 Nm)

300 ft. lbs.

(405 Nm)

Содержание 680S



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание 680S

Отзывы:

Похожие инструкции для 680S

Бренды по названию

Популярные бренды

JLG 680S, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание 680S

Отзывы:

Похожие инструкции для 680S

Бренды по названию

Популярные бренды