manualshive.com logo in svg

JLG 680S, Руководство по обслуживанию и ремонту, Страница: 470 / 530

Поделиться
Скачать
JLG 680S Скачать руководство пользователя страница 470

SECTION 6 - JLG CONTROL SYSTEM

6-54

3121234

Table 6-9. Diagnostic Trouble Code Chart (DTC)

DTC

Flash Code

Fault Message

Check

001

00

EVERYTHING OK

No response required for this DTC.

002

00

GROUND MODE OK

No response required for this DTC.

0010

00

RUNNING AT CUTBACK - OUT OF TRANSPORT POSITION

Response described in Drive
Modes section.

000

00

<<< HELP COMMENT >>>

0011

00

FSW OPEN (Foot switch open)

The UGM shall not Enable the
Machine.

0012

00

RUNNING AT CREEP - CREEP SWITCH OPEN

The UGM shall limit the
machine to Creep speed.

0013

00

RUNNING AT CREEP - TILTED AND ABOVE ELEVATION

0014

00

CHASSIS TILT SENSOR OUT OF RANGE

Not reported during power-up.

0015

00

LOAD SENSOR READING UNDER WEIGHT

0031

00

FUEL LEVEL LOW - ENGINE SHUTDOWN

Response described in Fuel Shutdown section.

0035

00

APU ACTIVE

Response described in Auxiliary Power/Emergency Descent Mode section.

0039

00

SKYGUARD ACTIVE - FUNCTIONS CUTOUT

Response described in Sky-
Guard section.

0040

00

RUNNING AT CREEP - CREEP SWITCH CLOSED

210

21

<<< POWER-UP >>>

211

21

POWER CYCLE

212

21

KEYSWITCH FAULTY

The UGM shall assume a station selection of Ground.

213

21

FSW FAULTY

The UGM shall not Enable the
Machine.

220

22

<<< PLATFORM CONTROLS >>>

227

22

STEER SWITCHES FAULTY

The UGM shall prohibit Steer;
The UGM shall limit Drive to
Creep
The Steer Left switch input = Low;
The Steer Right switch input = Low;
Steer and full Drive speed permitted after
controls are initialized

2211

22

FSW INTERLOCK TRIPPED

Can be reported during power- up.

2212

22

DRIVE LOCKED - JOYSTICK MOVED BEFORE FOOTSWITCH

Can be reported during power- up.

2213

22

STEER LOCKED - SELECTED BEFORE FOOTSWITCH

The UGM shall not Enable the
Machine.

2214

22

DRIVE/STEER LOCKED - JOYSTICK MOVED BEFORE ENABLE

2216

22

D/S JOY. OUT OF RANGE HIGH

Resistive joysticks.
If the reference voltage is > 7.7V then the reference
voltage is out of tolerance of a short to battery has
occurred.

2217

22

D/S JOY. CENTER TAP BAD

Resistive joysticks.
- There is a +/-.1V range. around these values due to
resistor tolerances.

2219

22

L/S JOY. OUT OF RANGE HIGH

Resistive joysticks.
- If the reference voltage is > 7.7V then the reference
voltage is out of tolerance of a short to battery has
occurred.

Содержание 680S



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов