JLG 680S Скачать руководство пользователя страница 440 | Manualshive

Страница: 440 / 530

background image

SECTION 6 - JLG CONTROL SYSTEM

6-24

3121234

6.3

MACHINE ORIENTATION WHEN DOING SPEED
TESTS

Lift

: Telescope Retracted. Lift Up, and Record Time. Lift Down

and Record Time.

Swing

: Boom lift at Full Elevation, Telescope Retracted, Swing

360 degrees and Record Time. Swing the Opposite 360
degrees and Record Time.

Telescope

: Boom lift at Full Elevation, Telescope Out and

Record Time. Telescope In and Record Time.

Drive (Forward/Reverse)

: Test should be done on a smooth

level surface. Drive Select Switch should be set to High Engine.
Results should be recorded for a 200 ft. course. Drive Forward,
Record Time. Drive Reverse, Record Time.

Drive (Elevated)

: Test should be done on a smooth level sur-

face. Drive Select Switch should be set to High Engine. Results
should be recorded for a 50 ft. course. Drive Forward, Record
Time. Drive Reverse, Record Time.

Platform Rotate

: Platform level and completely rotated one

direction. Rotate 180 degrees and Record Time. Rotate the
other direction, Record Time.

Test Notes

1.

Stop watch should be started with the function, not
with the controller or switch.

2.

All speed tests are run from the platform. These speeds
do not reflect the ground control operation.

3.

The platform speed knob control must be at full speed
(turned clockwise completely).

4.

Function speeds may vary due to cold, thick hydraulic
oil. Test should be run with the oil temperature above
100° F (38° C).

5.

Some flow control functions may not work with the
speed knob clicked into the creep position.

Table 6-6. Function Speeds (In Seconds)

Function

680S

Main Lift Up

59-75

Main Lift Down

57-75

Swing Right & Left*

110-135

NOTE:

No more than 10% difference between swing left and
swing right.

Main Telescope Out

50-56

Main Telescope In

38-49

Platform Rotate Right & Left*

18-30

NOTE:

No more than 15% difference between rotate left and
rotate right.

Drive (Forward)

33-45

Drive (Reverse)

33-45

Drive (Elevated)

46-75

4150384 M

«
...
438
439
440
441
442
...
»

Содержание 680S



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 680S

Бренд: National Comfort Products Страницы: 28

Бренд: Omega Lift Страницы: 24

Бренд: Omega Lift Страницы: 8

Бренд: OMA Страницы: 45

Бренд: Clarke Страницы: 24

Бренд: M-system Страницы: 10

Бренд: M-system Страницы: 10

Бренд: M-system Страницы: 5

Бренд: Triax Страницы: 52

ProcessLogix 1757-SRM

Бренд: Allen-Bradley Страницы: 36

Бренд: Danfoss Страницы: 44

Бренд: Ravaglioli Страницы: 98

HERCULES 6.5 PLUS

Бренд: Fenix Страницы: 24

Бренд: Allmatic Страницы: 32

Бренд: SUNSTONE Страницы: 12

Бренд: ICP DAS USA Страницы: 2

PULSEMIG 300-T2

Бренд: IMS Страницы: 76

OPTIMARC CV355P

Бренд: Lincoln Electric Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды