manualshive.com logo in svg

JLG 680S, Руководство по обслуживанию и ремонту

JLG 680S – это мощная платформа с большой грузоподъемностью. Для обеспечения долговечности и безопасной эксплуатации необходимо регулярное обслуживание. Скачайте инструкцию по обслуживанию и ремонту бесплатно на manualshive.com и следуйте ей для сохранения высокой производительности вашего оборудования.

Поделиться
Скачать
background image

SECTION 5 - BASIC HYDRAULICS INFORMATION & SCHEMATICS

5-70

3121234

Start-up Procedure

When initially starting a new or a rebuilt transmission system.
it is extremely important that the start-up procedure be fol-
lowed. It prevents the chance of damaging the unit which
might occur if the system was not properly purged of air
before start-up.

1.

After the transmission components have been properly
installed, fill the servo pump housing at least half full
with filtered system oil. Connect all hydraulic lines and
check to be sure they are tight.

2.

Install and adjust all control linkage.

3.

Fill the reservoir with an approved oil that has been fil-
tered through a 10 micron filter. Refer to Eaton Hydrau-
lics Technical Data sheet number 3-401 titled Hydraulic
Fluid Recommendations.

4.

Gasoline or L.P. engines: remove the coil wire and turn
the engine over for 15 seconds. Diesel engines: shut off
the fuel flow to the injectors and turn the engine over
for 15 seconds.

5.

Replace the coil wire or return the fuel flow to the injec-
tors. Place the transmission unit in the neutral position,
start the engine and run it at a low idle. The charge
pump should immediately pick up oil and fill the system.
If there is no indication of fill in 30 seconds, stop engine
and determine the cause.

6.

After the system starts to show signs of fill, slowly move
pump swashplate to a slight cam angle. Continue to
operate system slowly with no load on motors until sys-
tem responds fully.

7.

Check fluid level in the reservoir and refill if necessary to
the proper level with an approved filtered oil.

8.

Check all line connections for leaks and tighten if neces-
sary.

9.

The machine is now ready to be put into operation.

10.

Frequent filter changes are recommended for the first
two changes after placing the machine back into opera-
tion. Change the first filter in 3-5 hours and the second
at approximately 50 hours. Routinely scheduled filter
changes are recommended for maximum life of the
hydraulic system.

Содержание 680S



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 680S

rav KT100 Operating Instructions Manual preview
KT100
Бренд: rav Страницы: 120
ubbink Ubiflux F300 Installation Instructions Manual preview
Ubiflux F300
Бренд: ubbink Страницы: 7
Valx Landing leg H Installation And Operation Instructions Manual preview
Landing leg H
Бренд: Valx Страницы: 28
M-system R7D-YV2A Instruction Manual preview
R7D-YV2A
Бренд: M-system Страницы: 10
M-system R7D-YS2A Instruction Manual preview
R7D-YS2A
Бренд: M-system Страницы: 10
M-system R30SVF4 Instruction Manual preview
R30SVF4
Бренд: M-system Страницы: 5
Triax 492060 User Manual preview
492060
Бренд: Triax Страницы: 52
Velux ACTIVE KIX 300 Installation Instructions Manual preview
ACTIVE KIX 300
Бренд: Velux Страницы: 24
Polyaire Zonemaster ZoneTouch V2 Installation Manual preview
Zonemaster ZoneTouch V2
Бренд: Polyaire Страницы: 24
STAMOS Power2 S-MAG 180 User Manual preview
Power2 S-MAG 180
Бренд: STAMOS Страницы: 282
Firepower FP 95 FC Operating Manual & Installation Manual preview
FP 95 FC
Бренд: Firepower Страницы: 52
NAUSICAA Weighing System User Manual preview
Weighing System
Бренд: NAUSICAA Страницы: 16
F.F. Group DWM 140 EASY Original Instructions Manual preview
DWM 140 EASY
Бренд: F.F. Group Страницы: 82
Elettro CF TIG 3510 Instruction Manual preview
TIG 3510
Бренд: Elettro CF Страницы: 38
Stanley STAR 2500 User Manual preview
STAR 2500
Бренд: Stanley Страницы: 32
ETC Insight 2x User Manual preview
Insight 2x
Бренд: ETC Страницы: 386
Basler DECS-400 Instruction Manual preview
DECS-400
Бренд: Basler Страницы: 12
ALFRA 41250 Operation Manual preview
41250
Бренд: ALFRA Страницы: 9

Бренды по названию

Популярные бренды

Загрузить еще бренды