JLG 680S Скачать руководство пользователя страница 335 | Manualshive

Страница: 335 / 530

background image

SECTION 4 - BOOM & PLATFORM

3121234

4-71

Diagnostic & Troubleshooting

If you are experiencing a problem that is not described here, see
your authorized dealer for service.

1.

Check the configuration under the menu “MACHINE
SETUP



STOUCH/SKYGUARD” according to the actual

system installed on machine. Make sure recommended
configuration described is selected.

If SkyGuard does Not Function with sensor engaged.

AUTHORIZED TECHNICIAN OR OPERATOR IS REQUIRED TO CONDUCT AN OPER-
ATION CHECK OF SKYGUARD SENSOR DAILY.

Help menu or diagnostics menu is to be used to collect
the fault information.

Depending on configurations, diagnostics menu
will read:

Diagnostics->System->Skyguard switch

Diagnostics->System->STOUCH OR SG

Pressing to engage the SkyGuard sensor will change the
switch or relay to open/close status.

If the switch status stays in “Open” while the actual Sky-
Guard sensor is pressed, then the SkyGuard sensor may
have failed, it needs to be changed immediately.

2.

If machine operation is not available:

Help menu or diagnostics menu is to be used to collect
the fault information.
Depending on configuration, diagnostics menu
will read:

Diagnostics->System->Skyguard switch

Diagnostics->System->STOUCH OR SG

Pressing to engage the SkyGuard sensor will change the
switch or relay to open/close status.

If the switch status states “Closed” regardless of sensor
activation status:

Power or ground wire is not making good contact and/
or may be loose or broken.

Both relays failed (low probability).

If the switch status is in disagreement, then one relay
may have failed or one relay isn't inserted into the
holder correctly. This may also be noticed since machine
will not be able to be operated.

Switch disagreement fault (2563) and SkyGuard switch
activation fault (0039) will be shown under
Help menu.

Table 4-2. SkyGuard Function Table

Main

Lift

Main Tele

In

Main Tele

Out

Main

Swing

Drive Forward

Drive Reverse

Basket

Level

Basket
Rotate

DOS

Enabled

DOS

Not

Enabled

DOS

Enabled

DOS

Not

Enabled

R

C

R

R

R

C*

R

R

C

C

R = Indicates Reversal is Activated

C = Indicates Cutout is Activated

* Disregard when boom is in line and driving forward with or without steering and no other function active

Note: When Soft Touch is enabled with SkyGuard all functions are cut out only.

«
...
333
334
335
336
337
...
»

Содержание 680S



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 680S

Бренд: Keithley Страницы: 97

Бренд: Happ Страницы: 52

Бренд: GANTERUD Страницы: 24

Бренд: National Instruments Страницы: 23

Бренд: Xantrex Страницы: 4

Бренд: Xantrex Страницы: 20

Бренд: Ravaglioli Страницы: 72

Бренд: ATEN Страницы: 176

Бренд: M-system Страницы: 3

Devicenet R7F4DD-DA16A-H

Бренд: M-system Страницы: 7

Бренд: Acard Страницы: 2

Бренд: ESAB Страницы: 44

Бренд: Thermal Arc Страницы: 56

Бренд: Keurig Страницы: 6

ProcessLogix 1757-SRM

Бренд: Allen-Bradley Страницы: 36

Бренд: ReadyLift Страницы: 20

Бренд: Pilz Страницы: 36

Бренд: Ingersoll-Rand Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды