manualshive.com logo in svg

JLG 680S, Руководство по обслуживанию и ремонту

JLG 680S – это мощная платформа с большой грузоподъемностью. Для обеспечения долговечности и безопасной эксплуатации необходимо регулярное обслуживание. Скачайте инструкцию по обслуживанию и ремонту бесплатно на manualshive.com и следуйте ей для сохранения высокой производительности вашего оборудования.

Поделиться
Скачать
background image

SECTION 4 - BOOM & PLATFORM

4-70

3121234

4.14 SKYGUARD

Operation

Skyguard is used to provide enhanced control panel protection.
When the SkyGuard sensor is activated, functions that were in
use at the time of actuation will reverse or cutout.

Functional Test

IF SKYGUARD SYSTEM IS INSTALLED ON MACHINE & 
“SKYGUARD” IS SELECTED IN MACHINE SET UP.

In Platform Mode:

1.

In an area free of obstructions, from the platform con-
trols test the SkyGuard feature by operating the tele-
scope out functions and engaging (and holding) the
SkyGuard sensor. Telescope function will be stopped
and telescope in function will be activated for a short
duration. Soft touch indicator light will flash at 3HZ,
horn will be turned on, until the SkyGuard sensor and
footswitch is disengaged. 

2.

With SkyGuard sensor engaged, press and hold the 
yellow “Override Soft Touch” button and then operate a
function switch or joystick to check if the operation can
be resumed. 

3.

Disengage the SkyGuard sensor, release controls, recycle
the foot switch, make sure normal operation available.

In Ground Mode:

Operation will be allowed regardless of SkyGuard sensor activa-
tion. 

IF SKYGUARD SYSTEM IS INSTALLED ON MACHINE & 
“BOTH” IS SELECTED.

In Platform Mode:

NOTE:

Machine will treat Soft Touch/SkyGuard override switch as
if it is a Soft Touch and SkyGuard switch.

1.

In an area free of obstructions, from platform controls
test the SkyGuard feature by operating the telescopic
out functions and engaging the SkyGuard sensor, tele-
scopic out function will be stopped, soft touch indicator
light will flash at 3HZ, the horn will be turned on until
the SkyGuard sensor and footswitch is disengaged. 

2.

With SkyGuard sensor engaged, press and hold the yel-
low  “Override  Soft  Touch”  button  and  then  operate  a
function switch or joystick to check if the operation can
be resumed. 

3.

Disengage the SkyGuard sensor, release controls, recycle
the foot switch, make sure normal operation is available. 

In Ground Mode:

Operation will be allowed regardless of SkyGuard switch activa-
tion.

IF SKYGUARD SYSTEM IS INSTALLED ON MACHINE & 
“SOFT TOUCH” IS SELECTED.

Machine will treat the Soft Touch/SkyGuard override switch as if
it is a Soft Touch switch.

IF SKYGUARD SYSTEM IS INSTALLED ON MACHINE & 
“NONE” IS SELECTED.

Skyguard sensor status will be ignored. No function cutout or
reversal will be implemented. 

Figure 4-26.  Skyguard

Содержание 680S



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 680S

KegLand BrewZilla 100L - Gen 4 Instruction Manual preview
BrewZilla 100L - Gen 4
Бренд: KegLand Страницы: 48
M-system R7F4DC-DA16A-H Instruction Manual preview
R7F4DC-DA16A-H
Бренд: M-system Страницы: 7
Miller Electric SWINGER 180 Installation, Operation & Maintenance Manual preview
SWINGER 180
Бренд: Miller Electric Страницы: 35
Ascon tecnologic vP4 Installation Manual preview
vP4
Бренд: Ascon tecnologic Страницы: 4
National Instruments SCXI SCXI-1102 Calibration Procedure preview
SCXI SCXI-1102
Бренд: National Instruments Страницы: 18
HEEVE FLEX H0067 Instruction Manual preview
FLEX H0067
Бренд: HEEVE Страницы: 8
Proslat HEAVY DUTY HOIST Installation Manual preview
HEAVY DUTY HOIST
Бренд: Proslat Страницы: 6
Salda RIS 700HE/HW EKO 3.0 Technical Manual preview
RIS 700HE/HW EKO 3.0
Бренд: Salda Страницы: 40
Tractel Davitrac Installation, Operating And Maintenance Manual preview
Davitrac
Бренд: Tractel Страницы: 162
HEIN-WERNER AUTOMOTIVE HW93805 Manual preview
HW93805
Бренд: HEIN-WERNER AUTOMOTIVE Страницы: 12
EWM Taurus **5 Basic S Series Operating Instructions Manual preview
Taurus **5 Basic S Series
Бренд: EWM Страницы: 41
salmson LIFTSON-S Installation And Starting Instructions preview
LIFTSON-S
Бренд: salmson Страницы: 20
Miller MTL-17 Owner'S Manual preview
MTL-17
Бренд: Miller Страницы: 32
Stel THOR 40H Instructions For Use And Maintenance Manual preview
THOR 40H
Бренд: Stel Страницы: 74
WELDING INDUSTRIES Synchro-Pulse CDT 450 CP38-3 Owner'S Manual preview
Synchro-Pulse CDT 450 CP38-3
Бренд: WELDING INDUSTRIES Страницы: 62
BOC Plasma 40 Torch Operating Manual preview
Plasma 40 Torch
Бренд: BOC Страницы: 12
Nussbaum HF 3S 8000 Operating Manual preview
HF 3S 8000
Бренд: Nussbaum Страницы: 72
Elatec TWN4 MultiTech 3 BLE Technical Handbook preview
TWN4 MultiTech 3 BLE
Бренд: Elatec Страницы: 13

Бренды по названию

Популярные бренды

Загрузить еще бренды