manualshive.com logo in svg

JLG 680S, Руководство по обслуживанию и ремонту

JLG 680S – это мощная платформа с большой грузоподъемностью. Для обеспечения долговечности и безопасной эксплуатации необходимо регулярное обслуживание. Скачайте инструкцию по обслуживанию и ремонту бесплатно на manualshive.com и следуйте ей для сохранения высокой производительности вашего оборудования.

Поделиться
Скачать
background image

SECTION 4 - BOOM & PLATFORM

3121234

4-67

Troubleshooting

Table 4-1. Troubleshooting

Problem

Cause

Solution

1.

Shaft rotates slowly or not at all

a.   Insufficient torque output

b.   Low rate of fluid flow

c.   Control or counterbalance valve has internal leak

d.   Piston and/or shaft seal leak

e.   Corrosion build-up on the thrust surfaces

f.   Swollen seals and composite bearings caused by incom-
patible hydraulic fluid

a.   Verify correct operating pressure. Do not exceed OEM’s
pressure specifications. Load may be above maximum
capacity of the actuator.

b.   Inspect ports for obstructions and hydraulic lines for
restrictions and leaks.

c.   Disconnect hydraulic lines and bypass valve. Leave valve
ports open and operate the actuator through housing ports
(do not exceed OEM’s operating pressure). The valve must
be replaced if a steady flow of fluid is seen coming from the
valve ports.

d.   Remove the plug and the housing’s valve ports. Operate
the actuator through the housing ports. Conduct the inter-
nal leakage test as described in the Section , Testing the
Actuator for Internal Leakage.

e.      Re-build  the  actuator.  Remove  all  rust  then  polish.
Replacement parts may be needed.

f.   Re-build the actuator. Use fluid that is compatible with
seals and bearings.

2.

Operation is erratic or not responsive

a.   Air in actuator

a.   Purge air from actuator. See bleeding procedures.

3.

Shaft will not fully rotate

a.   Twisted or chipped gear teeth overload conditions

b.   Port fittings are obstructing the piston during stroke

a.   Check for gear binding. Actuator may or may not be able
to be re-built and may need to be replaced.

b.   Check thread length of port fittings. Fittings should not
reach inside the housing bore.

4.

Selected position cannot be maintained

a.   Control or counterbalance valve has internal leak

b.   Piston and/or shaft seal leak

c.   Air in actuator

a.   Disconnect hydraulic lines and bypass valve. Leave valve
ports open and operate the actuator through housing ports
(do not exceed OEM’s operating pressure). The valve must
be replaced if a steady flow of fluid is seen coming from the
valve ports.

b.   Remove the plug and the housing’s valve ports. Operate
the actuator through the housing ports. Conduct the inter-
nal leakage test as described in the Testing section of this
manual.

c.   Purge air from actuator. See bleeding procedures

Содержание 680S



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 680S

Fandis TCU Series Operating Instructions Manual preview
TCU Series
Бренд: Fandis Страницы: 8
Fancom 743 Installer Manual preview
743
Бренд: Fancom Страницы: 31
3M SST Manual preview
SST
Бренд: 3M Страницы: 90
Garage Smart Hard Top Lifter User Manual preview
Hard Top Lifter
Бренд: Garage Smart Страницы: 20
IN-COMMAND NCSP35CM Installation And Operation Manual preview
NCSP35CM
Бренд: IN-COMMAND Страницы: 47
Westweld FLG-200HD Manual Instruction preview
FLG-200HD
Бренд: Westweld Страницы: 82
hotset C 148 Quick Start Manual preview
C 148
Бренд: hotset Страницы: 2
ThermoSoft NeverFreeze SX-0810-24 Manual preview
NeverFreeze SX-0810-24
Бренд: ThermoSoft Страницы: 5
GE Multilin GEK-113328A Instruction Manual preview
Multilin GEK-113328A
Бренд: GE Страницы: 218
R-Tech TIG315 Operation Instructions Manual preview
TIG315
Бренд: R-Tech Страницы: 25
GreenTech pureHeat+ Owner'S Manual preview
pureHeat+
Бренд: GreenTech Страницы: 12
Campbell Hausfeld WG4000 Operating Instructions And Parts Manual preview
WG4000
Бренд: Campbell Hausfeld Страницы: 48
Selco Genesis 3200 TLH Instruction Manual preview
Genesis 3200 TLH
Бренд: Selco Страницы: 272
Dannmar D-12 Series User Manual preview
D-12 Series
Бренд: Dannmar Страницы: 40
UHPPOTE HBK-D01 User Manual preview
HBK-D01
Бренд: UHPPOTE Страницы: 12
Elettro CF PRO MIG 276 Instruction Manual preview
PRO MIG 276
Бренд: Elettro CF Страницы: 20
GeoVision GV-NET/IO Instruction Manual preview
GV-NET/IO
Бренд: GeoVision Страницы: 4
Sherman DIGITIG 200GD Instruction Manual preview
DIGITIG 200GD
Бренд: Sherman Страницы: 14

Бренды по названию

Популярные бренды

Загрузить еще бренды