JLG 680S Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 530

background image

SECTION 1 - SPECIFICATIONS

3121234

1-11

1.11 DRAINING OIL BUILD UP FROM THE PROPANE

REGULATOR (PRIOR TO SN 0300134626)

During the course of normal operation oils may build
inside the primary and secondary chambers of the pro-
pane pressure regulator. These oils may be a result of poor
fuel quality, contamination of the fuel supply chain, or
regional variation in the make up of the fuel. If the build up
of the oil is significant this can effect the operation of the
fuel control system. Refer to Section 1.10, Operator Mainte-
nance for maintenance intervals. More frequent draining
may be required if the fuel supply has been contaminated.

FOR BEST RESULTS WARM THE ENGINE TO OPERATING TEMPERATURE BEFORE
DRAINING. THIS WILL ALLOW THE OILS TO FLOW FREELY FROM THE REGULA-
TOR.

1.

Move the equipment to a well ventilated area. Ensure
there are no external ignition sources.

2.

Start the engine and bring to operating temperature.

3.

With the engine running, close the manual tank valve
and run the engine out of fuel.

4.

Push in the Emergency Switch once the engine stops.

5.

Disconnect the electrical connection to the LPG fuel
temperature sensor in the auxiliary fuel port of the EPR.

6.

Remove the retainer clip for the LPG fuel temperature
sensor and remove the sensor from the regulator body.

NOTE:

Have a small container ready to collect oil that will

drain freely from the regulator at this point.

7.

Once all of the oil has been drained, reinstall the LPG
fuel temperature sensor and reconnect the electrical
connector.

8.

Open the fuel tank manual valve.

9.

Start the engine and verify all connections are secure.

10.

Dispose of any drained oil per local regulations in a safe
and proper fashion.

«
...
29
30
31
32
33
...
»

Содержание 680S



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 680S

Бренд: Geberit Страницы: 49

Бренд: R-Tech Страницы: 57

Бренд: ABICOR Страницы: 16

TIG 160 DC Lift

Бренд: GYS Страницы: 20

Бренд: PROCRAFT Страницы: 25

AXE 320 PULSE smart

Бренд: Alfain Страницы: 13

Rotational R-450A

Бренд: Global Lift Страницы: 49

HomeMatic HMW-IO-12-FM

Бренд: eQ-3 Страницы: 36

Smarty 4X P Series

Бренд: Salda Страницы: 30

Бренд: Gruetzner Страницы: 41

Бренд: WinSystems Страницы: 30

Бренд: TBM Страницы: 34

Бренд: ELEKTRA Страницы: 74

Бренд: HALDER Страницы: 2

Бренд: H&S AUTOSHOT Страницы: 19

Бренд: M-system Страницы: 4

Бренд: F.F. Group Страницы: 82

Бренд: Maxon Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды