JLG 680S Скачать руководство пользователя страница 243 | Manualshive

Страница: 243 / 530

background image

SECTION 3 - CHASSIS & TURNTABLE

3121234

3-191

Fuel Filter

After the fuel is drawn into the fuel pump, the fuel flows
through the gasoline fuel filter. The fuel filter will trap small
particles as the fuel passes through the filter to remove debris
and prevents the fuel pressure and temperature manifold and
fuel injectors from becoming damaged. Maintenance of the
fuel filter is required as indicated in Section 1.

Fuel Injector Rail

Fuel flows from the fuel pressure and temperature manifold
assembly to the fuel rails where the fuel is delivered to the fuel
injectors. The fuel rail also contains a Schrader valve which is
utilized to test the regulated pressure of the fuel system.

Fuel Injector

The fuel supply is maintained on the top of the injector from
the injector rail. The injector is fed a "pulse" signal through the
wire harness which causes the injector to open. During regular
operating conditions the ECM controls the opening and dura-
tion of opening of the injector. During lower RPM operation
the injector signals or "pulses" are less frequent then when the
engine is operating at higher RPMs. The engine has been cali-
brated to deliver the precise amount of fuel for optimum per-
formance and emission control.

3.28 GM ENGINE FUEL SYSTEM REPAIR

Propane Fuel System Pressure Relief

THE PROPANE FUEL SYSTEM OPERATES AT PRESSURES UP TO 312 PSI (21.5
BAR). TO MINIMIZE THE RISK OF FIRE AND PERSONAL INJURY, RELIEVE THE
PROPANE FUEL SYSTEM PRESSURE (WHERE APPLICABLE) BEFORE SERVICING
THE PROPANE FUEL SYSTEM COMPONENTS.

To relieve propane fuel system pressure:

1.

Close the manual shut-off valve on the propane fuel
tank.

2.

Start and run the vehicle until the engine stalls.

3.

Turn the ignition switch OFF.

RESIDUAL VAPOR PRESSURE WILL BE PRESENT IN THE FUEL SYSTEM. ENSURE
THE WORK AREA IS WELL VENTILATED BEFORE DISCONNECTING ANY FUEL
LINE.

Propane Fuel System Leak Test

NEVER USE AN OPEN FLAME OF ANY TYPE TO CHECK FOR PROPANE FUEL SYS-
TEM LEAKS.

Always inspect the propane fuel system for leaks after per-
forming service. Check for leaks at the fittings of the serviced
or replaced component. Use a commercially available liquid
leak detector or an electronic leak detector. When using both
methods, use the electronic leak detector first to avoid con-
tamination by the liquid leak detector.

«
...
241
242
243
244
245
...
»

Содержание 680S



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 680S

Бренд: Palfinger Страницы: 34

Бренд: JBM Страницы: 35

Бренд: SanRex Страницы: 4

TIG 160 DC Lift

Бренд: GYS Страницы: 20

Бренд: M-system Страницы: 7

Бренд: Everlast Страницы: 30

Бренд: Unimig Страницы: 14

Trailblazer 251

Бренд: Miller Страницы: 48

USB-1408FS-Plus-OEM

Бренд: Measurement Computing Страницы: 26

Бренд: jablotron Страницы: 3

Бренд: Pilz Страницы: 36

AIR ADJUST 2940

Бренд: Yetter Страницы: 64

Бренд: INVERTEC Страницы: 36

Бренд: morse Страницы: 5

Бренд: Miller Electric Страницы: 90

Бренд: Lincoln Electric Страницы: 64

Бренд: morse Страницы: 6

Бренд: ZONEMASTER Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды