manualshive.com logo in svg

JLG 680S, Руководство по обслуживанию и ремонту

JLG 680S – это мощная платформа с большой грузоподъемностью. Для обеспечения долговечности и безопасной эксплуатации необходимо регулярное обслуживание. Скачайте инструкцию по обслуживанию и ремонту бесплатно на manualshive.com и следуйте ей для сохранения высокой производительности вашего оборудования.

Поделиться
Скачать
background image

SECTION 3 - CHASSIS & TURNTABLE

3-190

3121234

Heated Exhaust Gas Oxygen Sensor

There are two Heated Exhaust Gas Oxygen Sensors (HEGO).

The first HEGO is mounted in the exhaust system downstream

of the engine. It is used to measure the amount of oxygen

present in the exhaust stream and communicate that to the

ECM via an electrical signal. The amount of oxygen present in

the exhaust stream indicates whether the fuel/air ratio is too

rich or too lean. If the HEGO sensor signal indicates that the

exhaust stream is too rich the ECM will decrease or lean the

fuel mixture during engine operation, if the mixture is too lean

the ECM will richen the mixture. The ECM continuously moni-

tors the HEGO sensor output. If a rich or lean condition is pres-

ent for an extended period of time, and the ECM cannot

correct the condition, the ECM will set a diagnostic code and

turn on the MIL light in control box.

The second HEGO is mounted in the exhaust system after the

muffler. It measures the amount of oxygen in the exhaust sys-

tem after the catalyst treatment has been completed in the

muffler. If the ECM detects that the catalytic action in the muf-

fler is not sufficient and fuel correction cannot correct the mal-

function the MIL light is illuminated in the control box and a

DTC code will stored in the computer.

THE HEATED EXHAUST GAS OXYGEN SENSOR IS AN EMISSION CONTROL

DEVICE. IF THE HEGO FAILS TO OPERATE, REPLACE IT WITH AN OEM REPLACE-

MENT PART. THE HEGO SENSOR IS SENSITIVE TO SILICONE OR SILICONE

BASED PRODUCTS AND CAN BECOME CONTAMINATED. AVOID USING SILICONE

SEALERS OR HOSES TREATED WITH SILICONE LUBRICANTS IN THE AIR

STREAM OR FUEL LINES.

Gasoline Multi Point Fuel Injection System (MPFI)

The primary components of the Gasoline Multi Point Fuel

Injection (MPFI) fuel system are the fuel tank, electric fuel

pump, fuel pressure and temperature sensor manifold, fuel fil-

ter and fuel rail.

Gasoline Fuel Pump

The Gasoline is stored as a liquid in the fuel tank and in drawn
into the fuel system by an electric fuel pump. The fuel pump
will receive a signal from the ECM to prime the fuel system for
approximately 2 seconds prior to start. Priming of the fuel sys-
tem provides for a quicker start, when the engine begins to
crank.

Gasoline Pressure and Temperature Sensor 
Manifold

This engine is equipped with a fuel injector rail that does not
have a pressure regulator or a return circuit to the fuel tank.
Fuel pressure for this engine is regulated by the engine’s ECM.
The ECM receive fuel pressure and temperature feedback from
the gasoline fuel sensor manifold and uses this information to
control the ground side of the fuel pump. Fuel pressure is reg-
ulated by the ECM pulse width modulating (PWM) the fuel
pump. The fuel pressure and temperature sensor manifold has
a return or "bleed" circuit that connects back to the fuel tank.
This circuit is used to bleed off any vapor that develops in the
line and return a small amount of fuel to the tank. The fuel
comes from the fuel tank and passes through the fuel pump.
Fuel exits the fuel pump, passes through the filter and then
enters the fuel pressure and temperature manifold assembly.
Fuel flows through the feed circuit and is delivered to the fuel
injector rail. Fuel that enters the bleed circuits through they
bypass valve in the manifold is returned to the fuel tank.

Figure 3-123.  Heated Exhaust Gas Oxygen Sensor 

(HEGO)

Figure 3-124.  Gasoline Fuel Pressure and Temperature 

Manifold Assembly

Содержание 680S



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 680S

National Instruments C Series Calibration Procedure preview
C Series
Бренд: National Instruments Страницы: 8
Rain Bird IQ Installation & User Manual preview
IQ
Бренд: Rain Bird Страницы: 48
Datavideo RMC-230 Instruction Manual preview
RMC-230
Бренд: Datavideo Страницы: 17
Tanco Autowrap 1300 EH Operator'S Manual preview
1300 EH
Бренд: Tanco Autowrap Страницы: 3
probst TAS-UNI Translation Of Original Operating Instructions preview
TAS-UNI
Бренд: probst Страницы: 33
EWM Saturn 351 DG Operating Instructions Manual preview
Saturn 351 DG
Бренд: EWM Страницы: 33
NEC Display Solutions SB-09HC User Manual preview
SB-09HC
Бренд: NEC Display Solutions Страницы: 4
Miller Electric MTTC-1512HR Owner'S Manual preview
MTTC-1512HR
Бренд: Miller Electric Страницы: 18
H&H US-511 Operation Manual preview
US-511
Бренд: H&H Страницы: 23
Custom Equipment Hy-Brid Lifts HB-830CE Maintenance & Troubleshooting Manual preview
Hy-Brid Lifts HB-830CE
Бренд: Custom Equipment Страницы: 29
XPR Access MTPX-RS-MF User Manual preview
MTPX-RS-MF
Бренд: XPR Access Страницы: 4
WARPP INTIG-200IDS Owner'S Manual preview
INTIG-200IDS
Бренд: WARPP Страницы: 19
Parweld XTM404S Operator'S Manual preview
XTM404S
Бренд: Parweld Страницы: 20
Intermatic PJB2175 Installation, Operation & Service Manual preview
PJB2175
Бренд: Intermatic Страницы: 2
FAAC J355HA M50 Translation Of The Original Instructions preview
J355HA M50
Бренд: FAAC Страницы: 16
Revo TX341 Operating Instructions Manual preview
TX341
Бренд: Revo Страницы: 6
WAGO I/O SYSTEM 750 750-421 Manual preview
I/O SYSTEM 750 750-421
Бренд: WAGO Страницы: 12
WALTCO GT-33 Installation Manual preview
GT-33
Бренд: WALTCO Страницы: 44

Бренды по названию

Популярные бренды

Загрузить еще бренды