manualshive.com logo in svg

JLG 340AJ, Руководство по обслуживанию и ремонту

JLG 340AJ - Универсальный подъемник для работы на высоте. Для правильного обслуживания и ухода за этим продуктом рекомендуется скачать бесплатное Руководство по обслуживанию и техническому обслуживанию с нашего веб-сайта. Главное внимание уделено безопасности и надежности. Безопасность - наш приоритет.

Поделиться
Скачать
background image

SECTION 6 - JLG CONTROL SYSTEM

3121259

– JLG Lift –

6-45

Troubleshooting

The following tables are furnished to provide possible resolu-
tions for common difficulties. Difficulties are classified as Gen-
eral, Calibration, Measurement Performance, and Host System
Functionality. 

Table 6-13.  LSS Troubleshooting Chart

Difficulty

Possible Resolution

Empty Platform Weight (DIAGNOSTICS, PLAT-
FORM LOAD) is not within ±15lbs (±7kg) of 
zero.

or

Platform Load readings (DIAGNOTICS, PLTLOAD) 
are unstable by more than ±2lbs (±1kg) (with-
out the influence of vibration or wind).

or

There are large variations in Platform Load 
(DIAGNOSTICS, PLTLOAD) based on the location 
of the load. Tolerance to variations is 20lbs for 
an evaluation using the technician’s weight, 
and +5% of Rated Load when using calibrated 
weights.

The LSS System is unable to properly measure the platform weight. 

1.  The Load Cell is not properly plugged into the LSS Harness. It is possible poor electrical contact is made.

2.  Wiring leading to the Load Cell is damaged. Carefully inspect sensor wiring where it passes through cable clamps for signs of damage. 
Inspect wiring where damage to the channel is apparent. 

3.  The Load Cell was not assembled properly during installation. Examine the sensor’s reading using the JLG Analyzer. Proceed to the DIAG-
NOSTICS, CELL, LOAD displays and determine if the readings are reasonable. It is often helpful to apply slight downward pressure above the 
sensor and observe that its output increases (increasing force measurement; decreasing means the sensor is mounted upside-down). 

4.  The Load Cell is contaminated by debris or moisture. Examine the sensor’s reading using the JLG Analyzer. Proceed to the DIAGNOSTICS, 
CELL, LOAD displays and determine if the readings are reasonable and stable (not changing by more than ±2lbs (±1kg) (without the influ-
ence of vibration or wind). Lack of measurement stability is a key indication of contamination. Unplug the connector and inspect for dirt or 
moisture. Look carefully into the female connector on the sensor’s cordset for evidence of contamination. Debris should be brushed away 
with a soft bristle brush (do not introduce any cleaners as they will leave conductive residue). Moisture should be allowed to evaporate or 
accelerated with a heat-gun (use low heat and be carefully to not melt connector materials). Moisture intrusion into the molded portion of 
the connector (capillary action into the wire bundle) or the Shear Beam Load Cell itself will require replacement of the sensor.

5.  The Load Cell has been mechanically damaged. If the Load Cell is physically deformed or has damage to the cover it should be replaced 
immediately. It is also possible to have invisible mechanical damage resulting from an extreme overload (>6000lbs [>2722kg]).

The Visual and Audible Overload Warnings fail 
to sound when platform is loaded beyond Rated 
Load, or when simulated by unplugging the 
Load Cell. Controls remain functional at Plat-
form and Ground Control positions.

The Control System is failing to regard the overload signal from the LSS System, or the signal is shorted.

1.  The Load Sensing System must be enabled within the Control System. Plug the JLG Analyzer into the Control System, enter the Access 
Level 1 password (33271), and examine the MACHINE SETUP, LOAD sub-menu. The selection “2=CUTOUT PLT” should be displayed (plat-
form controls prevented during overload, ground controls remain operational). In country- or customer-specific circumstance, the selec-
tion “3=CUTOUT ALL” is used (platform and ground controls prevented during overload).

The Ground Audible Warning fails to sound, but 
the Platform Audible Warning sounds properly.

The Ground Alarm is missing or improperly installed. Verify that the device is mounted. Verify wiring from the Main Terminal Box and 
Ground Module. 

Controls remain functional at the Ground Con-
trol position during an overload, or when simu-
lated by unplugging the Load Cell. The Controls 
at the Platform Control position are prevented 
when using the engine, but not when using the 
Auxiliary Power Unit.

The JLG Control System is configured to prevent platform controls only in the event of overload. Alternately, the Host Control System can be 
configured to prevent ground and platform controls for country- or customer-specific circumstances.
Using the JLG Analyzer, enter the Access Level 1 password (33271). Proceed to the MACHINE SETUP, LOAD sub-menu. Set this parameter to 
“2=CUTOUT PLT” to prevent platform controls in the event of overload. Set this parameter to “3=CUTOUT ALL” to prevent platform and 
ground controls in the event of overload.

Содержание 340AJ



















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 340AJ

Upright AB46RT Operator'S Manual preview
AB46RT
Бренд: Upright Страницы: 48
Terex Gyro 4020 Service Manual preview
Gyro 4020
Бренд: Terex Страницы: 100
Mec 5492RT Operator'S Manual preview
5492RT
Бренд: Mec Страницы: 56
Mec 2033ES Service And Parts Manual preview
2033ES
Бренд: Mec Страницы: 260
Titan Lifts MRL-6000 Installation, Operation & Maintenance Manual preview
MRL-6000
Бренд: Titan Lifts Страницы: 20
Oshkosh Corporation JLG ES1330L Operation And Safety Manual preview
JLG ES1330L
Бренд: Oshkosh Corporation Страницы: 98
Oshkosh Corporation JLG 740AJ Operation And Safety Manual preview
JLG 740AJ
Бренд: Oshkosh Corporation Страницы: 134
Oshkosh JLG X17JP Service And Maintenance Manual preview
JLG X17JP
Бренд: Oshkosh Страницы: 128
Oshkosh JLG X1000AJ Service And Maintenance Manual preview
JLG X1000AJ
Бренд: Oshkosh Страницы: 162
Oshkosh Corporation JLG 1200SJP Operation And Safety Manual preview
JLG 1200SJP
Бренд: Oshkosh Corporation Страницы: 168
Oshkosh JLG 1043 Operation & Safety Manual preview
JLG 1043
Бренд: Oshkosh Страницы: 254
Oshkosh Corporation JLG E400AJP Service And Maintenance Manual preview
JLG E400AJP
Бренд: Oshkosh Corporation Страницы: 258
Oshkosh Corporation JLG 450AJ Service And Maintenance Manual preview
JLG 450AJ
Бренд: Oshkosh Corporation Страницы: 342
Mantall XE100C Original Instructions Manual preview
XE100C
Бренд: Mantall Страницы: 42
LGMG S0507SDTCE10 Operation And Maintenance Manual preview
S0507SDTCE10
Бренд: LGMG Страницы: 79

Бренды по названию

Популярные бренды

Загрузить еще бренды