JING JIE UniPBX-2000 Скачать руководство пользователя

Страница: 75 / 219

Using the System

The detail of each parameter is described as below:

Parameter

Name

Description

Office ID

Holiday

The holiday date in formation of MM/DD.

Description

The holiday name or description for this holiday.

Holiday Prompt

The holiday prompt could be used for this specified
holiday in menu editor.

2.3.1.5

Prompt File

To manage the office's prompt file, click

Prompt

button for this office and the office

belonged to this office will be listed. Once you click a prompt file name, you can play
to hear the voice or delete it. Click

Upload

and you will able to upload your own

recorded file into this office. The file format is showed as follows:
- 8K Sample Rate
- 16 bits
- Linear PCM (signed)
- Mono
- Wav format

Click Copy and you will able to copy prompts from a existing office. The prompt file
management page are showed as below:

Содержание UniPBX-2000




























































































































































































































Результаты поиска

Содержание UniPBX-2000

Отзывы:

Похожие инструкции для UniPBX-2000

Бренды по названию

Популярные бренды

JING JIE UniPBX-2000, Административное руководство

Результаты поиска

Содержание UniPBX-2000

Отзывы:

Похожие инструкции для UniPBX-2000

Бренды по названию

Популярные бренды