JING JIE UniPBX-2000 Скачать руководство пользователя страница 169

Страница: 169 / 219

Using the System

169

The administrator can set access deny, read only or full access right for each
module. Click

Apply

to save.

2.8.4

Clear Hitory Data

It is recommended to clean the unnecessary historical data periodically. Here is the
place to clean those historical data. Click

Administration -> Clear History Data

clean those historical data.

Select those data you want to delete, click apply to delete it.

2.8.5

Backup/Restore

Backup/Restore is used to backup the system configuration or restore it back. All the
configuration will be saved. Click

ADMINISTRATION -> Backup/Restore

to do the

backup to restore.

Select Backup System Configuration to backup the system configuration.
Select Restore System Configuration to restore it back.

2.8.6

Upgrade System

Use

Upgrade System

to do the application patch by clicking

ADMINISTRATION -

> Upgrade System

. Please only use the certificated patch file to do the upgrade.

Otherwise, it will had problems.

Содержание UniPBX-2000




























































































































































































































Результаты поиска

Содержание UniPBX-2000

Отзывы:

Бренды по названию

Популярные бренды

JING JIE UniPBX-2000, Административное руководство

Результаты поиска

Содержание UniPBX-2000

Отзывы:

Бренды по названию

Популярные бренды