JING JIE UniPBX-2000 страница 159 Скачать руководство пользователя | Manualshive

Страница: 159 / 219

background image

Using the System

159

Field Name

Description

IPV4 VIP for WAN

Virtual IP V4 address for WAN interface for HA Group 2.

IPV4 VIP for LAN

Virtual IP V4 address for LAN interface for HA Group 2.

IPV6 VIP for WAN

Virtual IP V6 address for WAN interface for HA Group 2. The
IPV6 address must be a global unicast addressed, not a link-
local or site-local address. IPV6 VIP for WAN is only available
when 1 Ethernet leg mode is used (Attached LAN Interface is
disabled).

IPV6 VIP for LAN

Virtual IP V6 address for WAN interface for HA Group 2.
Virtual IP V6 address for WAN interface. The IPV6 address
must be a global unicast addressed, not a link-local or site-
local address. It could be use fc00:xxxx:xxx:xxx as the private
IP V6 address. IPV6 VIP for LAN is only available when 2
Ethernet legs mode is used (Attached LAN interface is
enabled).

Service Controller

It is a internal status for HA resource status controlling.

2.7.5

Blocked IP

The system will detect the SIP attack such as "friendly scanner" or other potential
attack by the attacking behavior and blocked it automatically. A system alert event
will be written to system alert for auditing purpose. After the defined "Attack Block
Time" in Service Parameter is reached, the blocked IP will be released. The
administrator can query the current blocked IP address by clicking

DIAGNOSTIC ->

Blocked IP

. The following screen will appear.

The detail of each filed is described as below:

Field Name

Description

IP Address

The IP address was blocked by the system because of
SIP attack detected.

«
...
157
158
159
160
161
...
»

Содержание UniPBX-2000




























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для UniPBX-2000

Бренд: Toshiba Страницы: 368

AastraLink RP 500

Бренд: Aastra Страницы: 16

Carina PBX Lite

Бренд: Wahsega Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды