JING JIE UniPBX-2000 страница 147 Скачать руководство пользователя

Страница: 147 / 219

Using the System

147

The detail of each parameter is described as below:

Parameter Name

Description

Plan ID

The tariff plan ID

Pilot Number

The prefix to be matched the called number. Check
default tariff to set a default rate for this plan.

The prefix name

The name of this prefix

Charge Unit

The charge unit in seconds.

Charge Amount

The charge amount based on this unit.

2.6.3

Call History Detail Report

Call History Detail Report is used to show call list based on search condition. Click

BILLING -> Call History

Detail Report

to list the filtered calls. The search condition

will appear as follows:

You can select the search condition as above and click search to start the query. The
filtered Call History Detail Report will appear as follows:

Содержание UniPBX-2000




























































































































































































































Результаты поиска

Содержание UniPBX-2000

Отзывы:

Похожие инструкции для UniPBX-2000

Бренды по названию

Популярные бренды

JING JIE UniPBX-2000, Административное руководство

Результаты поиска

Содержание UniPBX-2000

Отзывы:

Похожие инструкции для UniPBX-2000

Бренды по названию

Популярные бренды