JING JIE UniPBX-2000 Скачать руководство пользователя

Страница: 143 / 219

Using the System

143

Field Name

Description

Peak Adhoc Conference

The peak service count for adhoc conference service.

Total Adhoc Conference

The total service count for adhoc conference service
within this period.

Voice Message

The service count for extension to extension voice mail
or direct to voice mail service.

Peak Voice Message

The peak service count for extension to extension
voice mail or direct to voice mail service.

Total Voice Message

The total service count for extension to extension voice
mail or direct to voice mail service.

2.6

Billing

The system has built-in billing to enterprise charge purpose. First, you need to create
a division and assign extension to it. Then you can you have enterprise, division and
extension level of billing report.

2.6.1

Division

Division is the managing and charging unit for enterprise. To have correct charge for
each division, you need assign extensions to it. Click

BILLING -> Division

to view

and change the division settings as follows:

Содержание UniPBX-2000




























































































































































































































Результаты поиска

Содержание UniPBX-2000

Отзывы:

Похожие инструкции для UniPBX-2000

Бренды по названию

Популярные бренды

JING JIE UniPBX-2000, Административное руководство

Результаты поиска

Содержание UniPBX-2000

Отзывы:

Похожие инструкции для UniPBX-2000

Бренды по названию

Популярные бренды