JING JIE UniPBX-2000 Скачать руководство пользователя

Страница: 106 / 219

106

Parameter Name

Description

SIP Trunk ID

SIP trunk ID

SIP Domain

The SIP register domain for SIP trunk user

The SIP User (normally, it is TEL number) for register

Registrar Server

The SIP registrar proxy server IP address or DNS name.

Registrar Port

The SIP service port to register (default value is 5060)

Outbound Proxy
Server

The SIP outbound proxy IP address or DNS name

Outbound Proxy Port

The outbound proxy service port (default value is 5060)

SIP Register User ID

The SIP user ID for authentication

SIP Register
Password

The SIP password for authentication

The register expires in seconds for SIP register. The
default is 600 seconds.

Permanent Contact

If this is checked, this SIP trunk will no register and use
peering instead.

Display Name of SIP
Trunk

The SIP Display Name will be used when this SIP trunk is
calling. The default is original caller's SIP TEL.

SIP ANI of SIP Trunk

The SIP TEL will be used when this SIP trunk is calling.
The default is SIP trunk's TEL.

Local Port

The local SIP port will be used for this SIP trunk. For most
of case, it will be 5060 port.

Description

The description for this SIP trunk

2.4.2

Routing Plan

The routing plan is used to provides different routing based on prefix, time of day,
dialed length and hunting type to decide where the call should be called. The
maximum Routing Plan could be created is 4096. Click

FEATURE -> Routing Plan

to view the current created routing plans as follows:

Содержание UniPBX-2000




























































































































































































































Результаты поиска

Содержание UniPBX-2000

Отзывы:

Похожие инструкции для UniPBX-2000

Бренды по названию

Популярные бренды

JING JIE UniPBX-2000, Административное руководство

Результаты поиска

Содержание UniPBX-2000

Отзывы:

Похожие инструкции для UniPBX-2000

Бренды по названию

Популярные бренды