Jide CARINO 67 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 48

Jide CARINO 67 Скачать руководство пользователя страница 41

Jidé s.a. – Rue des Meuneries 11 – B-4650 HERVE (Belgique) – Tél. +32 87 31.75.12 – Fax +32 87 31.75.11 –

www.jide.be

[email protected]

CARINO (EN) February 2020

41

Technical documents

Troubleshooting

Observations

Possible cause

Remedies

No lighting up

- Batteries

- Gas income

- Communication

- Blocking of electronic box

- Connection
- Pilot

- Replace the batteries of the electronic
box and/or of the remote control
- Check the opening of the valve
- Purge the duct
- Reset the remote control (point 3,
chapter user)
- Push on Reset
- Wait for the cooling
- Replace the box
- Check the connection of the cables
- Check ignition (intensity and position)
- Check piezo wiring
- Replace the pilot

Lighting of the pilot
but no of the burners

- Pilot

- Check the intensity of the flame
- Check if obstruction of the pilot
- Check thermocouple
- Check gas pressure
- Check type of gas

Very low, blue and/or
agitated flames

- Gas flow

- Chimney setting

- Vermiculite

- Sealing

- Check gas type and pressure
- Check injectors diameter
- Check chimney's setting (draft
reduction)
- Check vermiculite quantity in burners
trays
- Clean burners
- Check the sealing of the door and of
different access hatches of the insert

Very high, very
yellow and/or
transparent flames

- Gas flow

- Chimney setting

- Vermiculite

- Logs

- Check gas type and pressure
- Check injectors diameter
- Check chimney's setting (draft
reduction)
- Check vermiculite quantity in burners
trays
- Clean burners
- Check logs positions

«
...
39
40
41
42
43
...
»

Содержание CARINO 67

















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды