manualshive.com logo in svg

Jide CARINO 67, Руководство по установке, использованию и обслуживанию

Поделиться
Скачать
Jide CARINO 67 Скачать руководство пользователя страница 18

Jidé s.a. – Rue des Meuneries 11 – B-4650 HERVE (Belgique) – Tél. +32 87 31.75.12 – Fax +32 87 31.75.11 – 

www.jide.be

 - 

[email protected]

 

 

CARINO (EN)   February 2020 

 

 

18 

-

 

It is mandatory to install a block valve on gas inlet, close to the device and easily accessible. 

-

 

This device must be installed according to standard in force. It is asked to comply with local 
legislations for the installation of type C devices: 

o

 

Connection of the device must be done by a certified installer. Main standards to respect 
are  NBND51/003  and  NBN61002  for  Belgium,  NFD  35-377  or  DTU  P45-204.  If  no 
standards is specified, refer to NBN 61002 standard. 

o

 

If connection is done to an existing chimney which was previously used by a device using 
another combustible than gas, it is mandatory to sweep, clean and inspect the duct. The 
duct and its connection must be clean and sealed. 

-

 

Concentric  pipes  and  connection  pieces  used  must  be  EONTOP  METALOTERM  US100  or 
JEREMIAS (Detandt-Simon) TWIN K-100. For flexibles, use ducts in stainless steel.  You can buy 
EONTOP  connections  by  Jidé  (rue  des  Meuneries  11,  4650  Herve,  Belgium)  or  directly  by 
EONTOP  (Oude  Veerseweg  23,  4332  SH    Middelburg,  The  Netherlands)  and  JEREMIAS 
connections by Detandt-Simon (Rue d'Herchies 37, 7011 Ghlin, Belgium). 

-

 

Chimney settings authorised are only those mentioned in this manual. 

-

 

Read mindfully and entirely the manual before any use. 
 

 

Site preparation 

 
Dimensions of the recess and aeration around the fireplace 
 
The  recess,  i.e.  the  volume  around  the  fireplace,  has  to  contain  the 
appliance while providing an additional space of at least 5 mm (on the left 
and  right  sides,  and  above  the  fireplace)  in  order  to  accommodate 
expansion. Place the decorating frame and ensure a good airflow between 
the  insert  and  the  housing  (see  plan  in  attachment  at  the  end  of  the 
manual). There must be no masonry against the fireplace.  
 
Attention! The back offset of the concentric elbow is 3,5 cm. 
 
 
 
Insulation of the fireplace 
 
The  materials  used  must  be  non-inflammable.  Provide  high-temperature  insulation  around  the 
fireplace to protect certain materials. In this case we advise protecting the back, sides and top of the 
appliance. If no insulation has been provided, it is recommended keeping a distance of 5 cm from 
inflammable materials around the corner and 10 cm from the outlet nozzle, and to ventilate the 
recess. 
 
Your installer can advise you regarding the protection to be provided.  
 

 

3,5 cm 

Содержание CARINO 67

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды