JHCTech KMDA-3230 Скачать руководство пользователя страница 22

Страница: 22 / 76

User’s Guide

2.3.1 Ethernet Connector (LAN)

The KMDA-3230 is equipped with 4*Intel® I210AT (LAN1/LAN3/LAN4/LAN5) PCIe Gig. Ethernet for

10/100/1000Mbps adaptive; 1*Intel®I219LM (LAN2) support iAMT12.0. The product provides 5*RJ45,

with LED indicators on the front side to show its Active/Link status (Green LED) and Speed status

(yellow LED).

Table 2.1 for pin assignments.

Figure 2. 5

Table 2.1: RJ-45 Connector pin assignments

Pin 10/100/1000BaseT Signal

10/100/1000BaseT Signal

TX+(10/100), (GHz)

LAN_DC-(GHz)

TX-(10/100), LAN_DA-(GHz)

RX-(10/100), LAN_DB-(GHz)

RX+(10/100), (GHz)

LAN_DD-(GHz)

(GHz)

LAN_DD-(GHz)

2.3.2 USB Connector

The USB device allows data exchange between your computer and a wide range of simultaneously

accessible external Plug and Play peripherals.

The KMDA-3230 provides 4*USB3.1, 2*USB2.0 (one inside for dongle). The USB interface can be

disabled in the system BIOS setup.

Table 2.2 for USB2.0 pin assignments.

Содержание KMDA-3230













































































Результаты поиска

Содержание KMDA-3230

Отзывы:

Похожие инструкции для KMDA-3230

Бренды по названию

Популярные бренды

JHCTech KMDA-3230, Руководство пользователя

Результаты поиска

Содержание KMDA-3230

Отзывы:

Похожие инструкции для KMDA-3230

Бренды по названию

Популярные бренды