Jetter JM-105 Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 106

Jetter JM-105 Скачать руководство пользователя страница 71

JetMove 105

7.7 Connection of the Resolver

Jetter AG

71

7.7

Connection of the Resolver

7.7.1

Specification

Specification of the Connector for Terminal X61 (ENCODER)

• 15-pin high density SUB-D connector (male)
• Metallized enclosure

Specification of the Resolver Cable

• Cable cross-sectional area of at least 3 * 2 * 0.14 mm²
• Cores have to be shielded and twisted in pairs and have to be included in an

overall shielding

• The shield must be connected to the connector housings on both ends of the

cable with the greatest possible surface area.

• Material: Copper
• Temperature class: 60 °C
• Maximum cable length: 50 m

7.7.2

Resolver Cable With Mating Connector

The pre-fabricated resolver cable is used with the variants “Motor with male
connector” on page 54 and “Motor with screw clamping terminals and cables with
male connectors” on page 54.

Note!

The resolver respectively HIPERFACE mating connector of the synchronous
servo motor series JH, JL and JK can be ordered from Jetter AG by supplying the
following particulars:

Article # 15100069

Resolver / HIPERFACE

The complete resolver cable connecting the servo amplifier JetMove 105 and the
synchronous servo motor series JL1 and JH2 can be obtained from Jetter AG.
The resolver cable can be ordered by submitting the following cable
specifications and the respective cable length in cm:

KAY_0623_xxxx

For the servo amplifier series JetMove 105

«
...
69
70
71
72
73
...
»

Содержание JM-105











































































































Отзывы:

Нет отзывов