Jetter JM-105 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 106

Jetter JM-105 Скачать руководство пользователя страница 13

JetMove 105

1.1 General Safety Instructions

Jetter AG

13

1.1.5

Repair and Maintenance

Repairs to the digital servo amplifier JetMove 105 must not be carried out by the
operator. The servo amplifier JetMove 105 does not contain any parts to be repaired
by the operator.
For being repaired, the servo amplifier JetMove 105 must be sent to Jetter AG.

The digital servo amplifier JetMove 105 is maintenance-free. Therefore, absolutely
no inspection or maintenance works are required for the operation of this device.

1.1.6

Disposal

In case of obvious damage or erratic behaviour, the servo amplifier must not be used
any more.

When disposing of devices, the local environmental regulations must be complied
with.

You can disassemble the digital servo amplifier JetMove 105 into its main
components by unscrewing it (aluminum heat sink and side plate, steel casing cover,
PCBs).

«
...
11
12
13
14
15
...
»

Содержание JM-105











































































































Отзывы:

Нет отзывов