Jetter JetControl 365MC Скачать руководство пользователя страница 51

Страница: 51 / 148

Jetter AG

Identification and Configuration | 7

User Manual – JetControl 365MC

51 / 148

7.2 IP configuration

This chapter describes the IP configuration for the controller. The following pa-
rameters can be set:

■

IP address of the controller

■

Subnet mask

■

IP address of the default gateway

■

IP address of DNS server

■

Controller name

■

IP port number for the JetSym debugger

■

Basic port number for communication via JetIP

■

Name of the AutoCopy command file

7.2.1 Factory settings

Prior to shipment of the JC-365MC controller, various parameters are set to a de-
fault value. These parameters can be changed by the user.

Factory settings

Parameter

Value

IP address of the controller

192.168.1.1

Subnet mask

255.255.255.0

IP address of the default gateway

0.0.0.0

IP address of DNS server

0.0.0.0

Controller name

JC-365MC

IP port number for debugger

52000

IP port number for JetIP

50000

Name for AutoCopy command file

/SD/autocopy.ini

DIP switch sliders

DIP switch slider 1 = ON
All other DIP switch sliders = OFF

User's password

admin

admin

User's password

system

system

Tab. 29:

Factory settings

7.2.2 Determining the IP address of the controller using JetIPScan

Introduction

The JetIPScan tool lets you determine the IP address, subnet mask and the IP
address of the default gateway of the JC-365MC.

INFO

Downloading JetIPScan

Jetter AG provides the JetIPScan program on its homepage

http://www.jetter.de

You will find the file

jetipscan_1-11-00.zip

for download under

Downloads -

Software - Other Software Tools - JetIpScan

Contents of the ZIP
file

The zip file

jetipscan_1-11-00.zip

contains the following files:

■

The program JetIPScan_V_1-11-00.exe

■

The help jetipscan_01_help_en.png

■

The batch file read_IP_via_JETIPSCAN.bat to determine the IP address

Содержание JetControl 365MC





















































































































































Результаты поиска

Содержание JetControl 365MC

Отзывы:

Jetter JetControl 365MC, Руководство пользователя, Страница: 51 / 148

Результаты поиска

Содержание JetControl 365MC

Отзывы: