JETStream FXG2 Tornado Gun Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 38

JETStream FXG2 Tornado Gun Скачать руководство пользователя страница 1

Read these instructions thoroughly before installing, connecting, or using the
FXG2 TORNADO GUN. If any questions remain, call JETSTREAM at (800) 231-8192
or (832) 590-1300. Also read the yellow JETSTREAM SAFETY WARNING pamphlet
included with the shipment of your new FXG2 TORNADO GUN and reproduced
inside this publication. This product is sold with the understanding that the
purchaser agrees to thoroughly train all operators and maintenance personnel in
the correct and safe installation, operation and maintenance of the product and to
provide adequate supervision of personnel at all times. Retain these instructions
for future reference. If this product is resold or otherwise conveyed, purchaser
must pass on the instructions to the new user.

PRODUCT INSTRUCTIONS
FXG2 Tornado Gun™ (PNs 66210, 66211)
PI-120

The FXG2 Tornado Gun

TM

is an air-actuated, dual-trigger waterblast con-

trol gun that is designed for maximum operator safety and field durability.
The Tornado Gun utilizes a mandrel/seal configuration that can be easily
overhauled in the field, as well as pushlock-type air-hose connections for
ease of hose removal and/or replacement. The Tornado Gun is rated for
40,000 psi maximum operating pressure and utilizes a 9/16” Type M inlet
connection.

1
2
3
...
»

Содержание FXG2 Tornado Gun







































Отзывы:

Нет отзывов