JetCat SPH5 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 60

background image

Helicopter Head speed control menu

There is a sub menu in the turbine limits menu for altering the gear ratio of the
helicopter so as to set the head speed. Access it by entering the turbine limits
menu as before, then press limits and + simultaneously and release.

U-accel R1

:0.225

U-idle R1

:0.45

U-accel R2

:0.60

U-idle R2

:0.45

Nicad cells

6

Number of nicad cells powering the ECU

.

Leave at 6 if

using 2 LiPo cells

Ratio Turb -> Rot

9.73

Main gear to motor ratio. Adjust by pr/- keys
while holding down change value. Set this value for
your helicopter

Ratio Tail-> Rot

4.53

Main gear to tail rotor ratio. Adjust by pr/-
keys while holding change value key down. Set this
value for your helicopter

Once the gear ratio is set press menu key to return to turbine limits menu. Scroll
through with + key until you reach

maximum rpm. Set this at 165,000. The governor will

control the engine rpm but if you load the rotor head up the turbine may need to reach
this rpm.

Press the + key to scroll through until you reach ShaftHiR1:55,000 or some other
number. The 55,000 is the rpm of the secondary turbine and will be reduced by the
gearbox. Below that you will see ROT=1650 or some other number and Tail = 7422 or
some other number. This is the head speed and tail rotor speed in the computer at the
moment. To change the head speed to the desired value, press and hold the change
value and press the + or – keys. This will change the ShaftHiR1 value which will in turn
alter the ROT value. Set the ShaftHiR1 value so that the ROT value equals the head
speed you want. If you only want a single head speed setup then the AUX connection is
not used.

The V5 ECU has a 3 speed option for the head speed and this requires the addition of a
connection to the AUX lead on the ECU which needs to be connected to a 3 position

51

«
...
49
50
51
52
53
...
»

Содержание SPH5





























































Отзывы:

Нет отзывов

Похожие инструкции для SPH5

Бренд: TAYO Страницы: 42

Lombardini SILEO 1000

Бренд: Kohler Страницы: 168

Бренд: Germany Motions Страницы: 12

Бренд: MULTIPLEX modell Страницы: 6

ZA top SM225.40B

Бренд: ZIEHL-ABEGG Страницы: 76

Бренд: O.S. Speed Страницы: 4

Бренд: Honda Страницы: 16

Бренд: Honda Страницы: 16

Бренд: LONCIN Страницы: 24

Бренд: WEN POWER Страницы: 28

Бренд: LinMot Страницы: 24

Бренд: LinMot Страницы: 30

Бренд: Iveco Страницы: 74

Бренд: Marine Power Solutions Страницы: 24

Бренд: Marine Power Solutions Страницы: 22

Бренд: Marine Power Страницы: 12

Бренд: Marine Power Solutions Страницы: 23

Бренд: Marine Power Solutions Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды