JetCat SPH5 Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 60

background image

The R/C Check Menu

All parameters in this menu are for informational purposes only and will vary in
accordance with R/C input.

Value

Explanation

StickPuls

Throttle%

Position of the throttle stick (by percentage, 0-100%). An ‘F’ signals
a failsafe condition.
Position units of the throttle stick.

FailSafe Count

Displays the number of times the receiver went into failsafe during
the flight.

FailSafeTime
In seconds

Displays the time the receiver was in failsafe.

The INFO Menu

Info menu displays the following information:

Value

Explanation

BattCnd

Ubattery

The condition of the battery is indicated in the upper line:

1.

--OK--

2.

!WEAK!

3. --EMPTY--

1. If the battery voltage is 1.1V/Cell or higher “

—OK--

“ will be

displayed.

2. If the battery voltage drops under 1.1V/Cell, the display will

read “

!WEAK!”

. Red

Standby

and green

OK

LED’s will blink

simultaneously (at a rate of twice per second). Starting the
turbine is not possible, until the battery is recharged. If the
turbine is already running and the battery warning function is
enabled, the warning function will be activated.

3. If the battery voltage drops under 1.0V/Cell “—

EMPTY--

”

is

displayed. Starting the turbine is not possible until the battery
is recharged. If the turbine is running, it will be immediately
shut off, to avoid a malfunction of the ECU.

Current voltage of the battery. Displayed on bottom line.

Last Run Time

Last turbine run time.

Last-Off PmpVolt

Volts applied to the pump when it was switched off.

Last Off RPM

RPM of the turbine, when it was switched off.

Last Off TEMP

Temperature of the turbine, when it was switched off.

47

«
...
45
46
47
48
49
...
»

Содержание SPH5





























































Отзывы:

Нет отзывов

Похожие инструкции для SPH5

Бренд: BAFANG Страницы: 4

Бренд: Vascat Страницы: 60

Бренд: King Canada Страницы: 8

Бренд: Hyundai Seasall Страницы: 150

Бренд: Yanmar Страницы: 35

Бренд: Mitsubishi Страницы: 522

Бренд: DLE Страницы: 4

Бренд: Dietz Страницы: 12

Бренд: Gaspar Страницы: 53

Бренд: YANGDONG Страницы: 50

Бренд: Mitsubishi Страницы: 364

Бренд: Seidel Страницы: 12

Бренд: Hägglunds Страницы: 25

Бренд: Suzuki Страницы: 45

Бренд: Mack Страницы: 536

Бренд: Zenoah Страницы: 28

Бренд: YS Страницы: 2

Бренд: Daytona Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды