JetCat SPH5 Скачать руководство пользователя страница 46

Страница: 46 / 60

In addition to the default display, the following selections can be monitored on the upper
display line. Use the

◄

- /

►

keys alone for selecting the different parameters.

Value

Explanation

Default
Display

See above for description.

U-Pump /
RPM

Current pump voltage.
Current RPM.

Temp. /
RPM

Current EGT (

xhaust

emperature).

Current RPM.

OffCnd
SetRpm /
Set RPM

Last Off command (reason for shut down). See table on page 43.

Commanded RPM.

State /
RPM

Current turbine state.
Current RPM.

The Min/Max Menu

The Min/Max menu is used primarily for diagnostics purposes. All of the following
variables may be reset manually by pressing the

Change Value/Item

key on the GSU.

Although the display will indicate that the values cannot be changed, it will reset the
Min/Max values.

Value

Explanation

Upump-Max
Upump-Min

Maximum pump voltage.
Minimum pump voltage.

MaxTemp
MinTemp

Maximum EGT.
Minimum EGT.

AvgPump
AvgTemp

Average pump voltage
Average temperature

MaxRpm
MinRpm

Maximum turbine RPM.
Minimum turbine RPM.

AvgRpm
MaxRTmp

Average RPM
Average

temperature at maximum RPM during the last run.

Содержание SPH5




























































Результаты поиска

Содержание SPH5

Отзывы:

Похожие инструкции для SPH5

Бренды по названию

Популярные бренды

JetCat SPH5, Инструкция по эксплуатации

Результаты поиска

Содержание SPH5

Отзывы:

Похожие инструкции для SPH5

Бренды по названию

Популярные бренды