JetCat SPH5 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 60

background image

IMPORTANT:

IF YOU CHANGE YOUR TRANSMITTERS FAILSAFE AGAIN IN THE

FUTURE, YOU MUST REDUE THE FOLLOWING INSTRUCTIONS AGAIN

.

•

First, set your transmitters travel parameter to 100% for low throttle and 100% for

high throttle. On the JR 10X transmitter, use function 12 to access the throttle travel.

•

Set your transmitters failsafe for low throttle, low throttle trim. On the JR 10X

transmitter use function 77 to access the failsafe. Enable the throttle channel for a
failsafe (select

1

so the bar is in the top position

▀

) and then set the throttle stick and

throttle trim to their minimum positions. Save this minimum position by pressing

STORE

.

•

Return to the travel menu and now set the minimum and maximum throttle travel to

75%.

•

Now you must teach in these values into the ECU. Refer to

”Learn R/C”

section in

this manual for this procedure.

You can verify the failsafe function in the default GSU screen.

Default Display

This symbol will appear when in failsafe.

If you turn-off your transmitter, the default display will
indicate a failsafe by displaying an . If you turn the
transmitter back on, the will disappear. If the does not

appear when you turn-off your transmitter, the fail-safe is not programmed properly!

21

0.0

6.9

OC:----

You can verify the failsafe parameters by accessing the

RC Check Menu

. Press and

hold the

Select Menu

key on the GSU and by pressing the

►

+ key until the

RC-Check

Menu is displayed

. Now release the

Select Menu

key.

Time in Failsafe (seconds)

If you press the

◄

- in the RC-Check Menu until you see

FailSafeTime: the display will indicate the number of seconds
the reciever was in failsafe. This is a total time for all the
failsafe counts. If you turn-off your transmitter, it will increase

every second. This is a great tool for diagnosing the quality of the RC systems RF link
by checking this after each flight.

FailSafeTime (s)

:100.1

Number of Failsafes

If you press the

◄

- again you see Failsafe count: the display

will indicate the number of times the receiver went into
failsafe. If you turn-off and turn-on your transmitter, it will
increase this count by one. This is a great tool for diagnosing

the quality of the RC systems RF link by checking this after each flight.

FailSafe Count

:1

Refer to the Limits menu for the following parameters.

Failsafe delay

33

«
...
31
32
33
34
35
...
»

Содержание SPH5





























































Отзывы:

Нет отзывов

Похожие инструкции для SPH5

Бренд: Jacobsen Страницы: 103

Бренд: Ofna Racing Страницы: 2

Бренд: Jenny Science Страницы: 9

Бренд: Beckhoff Страницы: 31

Бренд: Baumr-AG Страницы: 25

Para-RC Cloud 0.5 ARF

Бренд: Hacker Страницы: 6

Бренд: Hacker Страницы: 8

Бренд: Hacker Страницы: 8

Бренд: STG-BEIKIRCH Страницы: 25

Бренд: FIAMA Страницы: 7

Бренд: YS Страницы: 2

Бренд: Yanmar Страницы: 65

Бренд: Yanmar Страницы: 248

Бренд: GSK Страницы: 24

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: Honda Страницы: 88

Z.28R Spec.3 Pullstart

Бренд: LRP electronic Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды