background image

 

GB - ENGLISH 

Operating Instructions 

 

Dear Customer, 

Many thanks for the confidence you have shown in us with the purchase of your new JET-machine. This manual has been 
prepared for the owner and operators of a JET JTS-315SP table saw to promote safety during installation, operation and 
maintenance procedures. Please read and understand the information contained in these operating instructions and the 
accompanying documents. To obtain maximum life and efficiency from your machine, and to use the machine safely, read 
this manual thoroughly and follow instructions carefully. 

…Table of Contents 

1. Declaration of conformity

 

2. Warranty

 

3.  Safety

 

Authorized use 
General safety notes 
Remaining hazards 

4. Machine specifications

 

Technical data 
Noise emission 
Contents of delivery 
Description of machine 

5. Transport and start up

 

Transport and installation 
Assembly 
Dust connection 
Mains connection 
Starting operation 

6. Machine operation

 

7. Setup and adjustments 

Changing saw blade 
Mounting the raving knife  
Mounting the saw guard  
Rising and tilting sawblade  
Rip fence setup 
Adjusting 90°stop 
Adjusting sawblade parallel 

8. Maintenance and inspection

 

9. Troubleshooting

 

10. Environmental protection

 

11. Available accessories

 

12. „Safe operation”

........ appendix A 

 

1.  Declaration of conformity 

On our own responsibility we hereby 
declare that this product complies 
with the regulations* listed on page 
2. Designed in consideration with the 
standards**. CE type examination*** 
performed by****. 

 

 

 

 

 

2.  Warranty 

The Seller guarantees that the 
supplied product is free from material 
defects and manufacturing faults. 
This warranty does not cover any 
defects which are caused, either 
directly or indirectly, by incorrect use, 
carelessness, accidental damage, 
repair, inadequate maintenance or 
cleaning and normal wear and tear. 

Guarantee and/or warranty claims 
must be made within twelve months 
from the date of purchase (date of 
invoice). Any further claims shall be 
excluded. 

This warranty includes all guarantee 
obligations of the Seller and replaces 
all previous declarations and 
agreements concerning warranties. 

The warranty period is valid for eight 
hours of daily use. If this is 
exceeded, the warranty period shall 
be reduced in proportion to the 
excess use, but to no less than three 
months. 

Returning rejected goods requires 
the prior express consent of the 
Seller and is at the Buyer’s risk and 
expense. 

Further warranty details can be found 
in the General Terms and Conditions 
(GTC). The GTC can be viewed at 
www.jettools.com or can be sent by 
post upon request. 

The Seller reserves the right to make 
changes to the product and 
accessories at any time. 

 

3.  Safety 

3.1 Authorized use 

This machine is designed for sawing 
wood, wood derived materials as well 
as similar to be machined hard 
plastics only. 
Machining of other materials is not 
permitted and may be carried out in 
specific cases only after consulting 
with the manufacturer.  

No metal workpieces may be 
machined. 

The workpiece must allow to safely 
be loaded, supported and guided. 

Do not cut round stock without 
suitable jigs or fixtures. The rotating 
saw blade could turn the work-piece. 

The proper use also includes 
compliance with the operating and 
maintenance instructions given in 
this manual. 
The machine must be operated only 
by persons familiar with its 
operation, maintenance and repair 
and who are familiar with its hazards. 
The required minimum age must be 
observed 

The machine must only be used in a 
technically perfect condition 
When working on the machine, all 
safety mechanisms and covers must 
be mounted. 

In addition to the safety requirements 
contained in this operating 
instructions and your country’s 
applicable regulations, you should 
observe the generally recognized 
technical rules concerning the 
operation of woodworking machines. 

Any other use exceeds authorization. 
In the event of unauthorized use of 
the machine, the manufacturer 
renounces all liability and the 
responsibility is transferred 
exclusively to the operator.  

 

3.2 General safety notes 

Woodworking machines can be 
dangerous if not used properly. 
Therefore the appropriate general 
technical rules as well as the 
following notes must be observed. 

Read and understand the entire 
instruction manual before attempting 
assembly or operation. 
Keep this operating instruction close 
by the machine, protected from dirt 
and humidity, and pass it over to the 
new owner if you part with the tool. 

No changes to the machine may be 
made. 

Daily inspect the function and 

Содержание JTS-315SP








Отзывы: