Jet JPJ-12B страница 3 Скачать руководство пользователя

Страница: 3 / 48

2.0

Table of Contents

Section

Page

1.0 Warranty and Service ..................................................................................................................................... 2

2.0 Table of Contents ........................................................................................................................................... 3

3.0 Safety Warnings ............................................................................................................................................. 4

4.0 Specifications ................................................................................................................................................. 6

5.0 Features and Terminology ............................................................................................................................. 7

6.0 Receiving ....................................................................................................................................................... 7

7.0 Unpacking ...................................................................................................................................................... 7

9.1 Contents of Shipping Container ................................................................................................................. 7

8.0 Electrical Connection ..................................................................................................................................... 7

9.0 Operating Controls ......................................................................................................................................... 8

9.1 Jointer to Planer Setup ............................................................................................................................... 8

9.2 Planer to Jointer Setup ............................................................................................................................... 8

9.3 Control Switch ............................................................................................................................................ 9

9.4 Planer Controls and Adjustments ............................................................................................................... 9

9.5 Jointer Controls and Adjustments .............................................................................................................. 9

10.0 Adjustments ............................................................................................................................................... 10

10.1 Fence Stop Adjustments ........................................................................................................................ 10

10.2 Table and Knife Adjustments ................................................................................................................. 11

10.3 Coplanar Alignment ................................................................................................................................ 11

10.4 Setting Knives at Correct Height and Parallel to Outfeed Table ............................................................ 13

10.5 Replacing Cutterhead Knives (Straight Knives Only) ............................................................................. 15

10.6 Replacing or Rotating Knife Inserts (Helical Cutterhead Only) .............................................................. 16

10.7 Jointer Table Lock Handle Adjustment ................................................................................................... 16

10.8 Belt Replacement ................................................................................................................................... 17

10.9 Feed Roller Height Adjustment .............................................................................................................. 18

10.10 Feed Roller Pressure Adjustment ........................................................................................................ 18

10.11 Planer Table Adjustment ...................................................................................................................... 19

11.0 Basic Operations ........................................................................................................................................ 20

11.1 Dust Collection ....................................................................................................................................... 20

11.2 Initial Startup .......................................................................................................................................... 20

11.3 Changing Mode of Operation ................................................................................................................. 20

11.4 Jointer Operations .................................................................................................................................. 20

11.5 Planer Operations .................................................................................................................................. 22

12.0 Maintenance ............................................................................................................................................... 23

12.1 Blade Care ............................................................................................................................................. 23

12.2 Sharpening the Knives (Straight Knives Only) ....................................................................................... 24

13.0 Lubrication .................................................................................................................................................. 24

14.0 Troubleshooting the JPJ-12B,JPJ-12BHH ................................................................................................. 25

14.1 Performance Troubleshooting

– Jointer ................................................................................................. 25

14.2 Performance Troubleshooting

– Planer .................................................................................................. 26

14.3 Mechanical Troubleshooting

– Planer/Jointer ........................................................................................ 27

15.0 Replacement Parts ..................................................................................................................................... 27

15.1 Infeed Table Assembly

– Exploded View ............................................................................................... 28

15.2 Infeed Table Assembly

– Parts List ........................................................................................................ 29

15.3 Outfeed Table Assembly

– Exploded View ............................................................................................ 30

15.4 Outfeed Table Assembly

– Parts List ..................................................................................................... 31

15.5 Cutterhead Assembly

– Exploded View ................................................................................................. 32

15.6 Cutterhead Assembly

– Parts List .......................................................................................................... 33

15.7 Planer Table Assembly

– Exploded View ............................................................................................... 34

15.8 Planer Table Assembly

– Parts List ....................................................................................................... 35

15.9 Blade Guard Assembly

– Exploded View ............................................................................................... 36

15.10 Blade Guard Assembly

– Parts List ...................................................................................................... 37

15.11 Gearbox Assembly

– Exploded View ................................................................................................... 38

15.12 Gearbox Assembly

– Parts List ............................................................................................................ 39

15.13 Cabinet Assembly

– Exploded View ..................................................................................................... 40

15.14 Cabinet Assembly

– Parts List ............................................................................................................. 41

15.15 Fence Assembly

– Exploded View ....................................................................................................... 43

15.16 Fence Assembly

– Parts List ................................................................................................................ 44

16.0 Electrical Connections for JPJ-12B, JPJ-12BHH ....................................................................................... 45

17.0 Optional Accessories ................................................................................................................................. 46

Содержание JPJ-12B

















































Результаты поиска

Содержание JPJ-12B

Отзывы:

Похожие инструкции для JPJ-12B

Бренды по названию

Популярные бренды

Jet JPJ-12B, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание JPJ-12B

Отзывы:

Похожие инструкции для JPJ-12B

Бренды по названию

Популярные бренды