background image

JET   

 

Setup and Assembly 

Any missing parts or damage should be reported 
immediately to your JET

®

 distributor. Do not use a 

damaged tool. Read this instruction manual 
thoroughly for operation, maintenance and safety 
instructions. 

Box contents: 

1 Flux 

chipper 

1  

Wide angle chisel 

Operation and parts manual  

1 Warranty 

card 

Operation 

 

The flux chipper must be 

properly lubricated before operation. See 
“Lubrication” section. 

 

Figure 1 

1. 

Rotate knurled collar until ball is aligned with 
hole in collar. 

2.  Insert chisel shank into cylinder, aligning 

notch in shank with ball.  

3. 

Rotate knurled collar 180-degrees in either 
direction to secure chisel shank. 

4. 

Remove protective cap from air inlet (Figure 
1). If an in-line oiler is not being used, add 4 
or 5 drops of air tool oil (not included) into the 
air inlet. 

5.  Blow out air line to remove any dirt or 

moisture, then connect air supply hose to 
tool. Set air pressure to 90 psi. 

IMPORTANT:

 Connecting a quick-change 

coupling directly to the tool is not 
recommended, as vibration may cause the 
connection to fail. Instead, add a leader hose 
and install any quick-change couplings 
farther down the line. 

6. 

Hold flux chipper firmly with both hands and 
rest chisel tip against work surface. 

7. 

Press throttle lever. Pressure against throttle 
lever determines speed of tool. Do not exert 
excessive pressure against work surface – 
let the tool do the work.  

8. 

Release throttle lever to stop flux chipper. 

9. 

To remove chisel, rotate knurled collar until 
hole aligns with ball. 

Maintenance 

Lubrication 

The flux chipper should be lubricated 

daily

 (or 

before each use) with air tool oil through the air 
inlet. During continual operation, it should be re-
oiled every 1 to 2 hours. This can be done with an 
in-line oiler, or manually. If done manually, 
proceed as follows: 

1. 

Disconnect air hose from tool. 

2. 

Place 4 or 5 drops of air tool oil into air inlet. 

NOTE: Air tool oil not provided; it is available 
at most major hardware and tool stores. SAE 
#10 oil or sewing machine oil may be used 
as a substitute. Do not use detergent oil. 

3.  Re-connect air. Run flux chipper at low 

throttle without load for a few seconds to 
distribute the oil throughout tool. 

4.  When finished operating flux chipper, 

disconnect air hose. Wipe off housing with a 
dry cloth. Place 4 or 5 drops of air tool oil into 
air inlet; re-connect air and run tool for a few 
seconds to distribute the oil. Disconnect air. 

Storage  

Avoid storing the flux chipper in very humid 
locations which promotes rusting of internal 
mechanisms. Always oil the tool and disconnect 
air hose before storage. 

Содержание JAT-820













Отзывы: