background image

 

- - 1 - - 

Jet Inc. 750 Alpha Drive Cleveland, OH 44143 www.jetincorp.com 800.321.6960 

    QA-SAL-132                 REV 7/31/2013 

 

Jet Inc. Model 197 Control Panel  

Installation and Users Manual

 

 

The Jet Incorporated Aerator control panel monitors and controls the operation of 
Jet system aerators and additional components. The panel can be configured to 
control single or dual aeration systems. A single aerator system controls the 
operation of one aerator. A dual aerator system can control two aerators, or one 
aerator and one re-aeration compressor. 
 
In addition to the aerator control circuits, the control panel also contains the 
following circuits or features: 
 

  Two aerator/compressor control circuits 

  Three auxiliary output circuits 

  Three auxiliary input circuits with normally open or normally closed 

selection 

  One power indicator LED, and four additional error indicator LED’s 

  An alarm buzzer with circuit board provision for an alternate or externally 

mounted buzzer 

  A 9-position DIP switch for selection of configuration options 

  User accessible reset switch and circuit board master reset switch 

  Alarm mode Auto-Dialer power and control interface 

  RS232 interface circuit 

  Circuit board mounted power switch and fuse 

 
 

Control Panel Features 

 

A.  Master Reset Button 
B.  Internal Horn 
C.  On/Off Switch 
D.  External Reset Button 
E.  Pump Power Supply Contacts 
F.  Alarm and Aerator Power Supply Contacts 
G.  Ground Buss 
H.  Central Alarm Beacon 
I.  DIP Switch Array 
J.  Auxiliary Alarm Settings (NC/NO) 
K.  Indicator Light Array 
L.  Auxiliary Alarm Contacts 
M.  Auxiliary Alarm Contacts 

 
 
 

Содержание 197















Отзывы: