6
Cabinet Dimensions
IMPORTANT:
If installing a range hood or microwave hood
combination above the cooktop, follow the range hood or
microwave hood combination installation instructions for
dimensional clearances above the cooktop surface.
A.
24" (61.0 cm) minimum
B.
Combustible area above countertop (shown by dashed
box above)
C.
30" (76.2 cm) minimum clearance between top of cooktop
platform and bottom of uncovered wood or metal cabinet
(24" [61 cm] minimum clearance if bottom of wood or
metal cabinet is covered by not less than 1/4" [6.4 mm]
flame retardant millboard covered with not less than No.
28 MSG sheet steel, 0.015" [0.04 mm] stainless steel, or
0.024" [0.06 mm] aluminum or 0.020" [0.05 mm] copper)
D.
13" (33 cm) recommended upper cabinet depth
E.
2
1
/
2
" (6.35 cm)
F.
19
5
/
16
" (49.0 cm) minimum, 19
3
/
8
" (49.3 cm) maximum
G.
18" (45.7 cm) minimum clearance from upper cabinet to
countertop within minimum horizontal clearances to
cooktop
H.
Grounded outlet: locate within 12" (30.5 cm) of right rear
corner of cutout
I.
23
1
/
2
" (59.7 cm) minimum, 23
5
/
8
" (60.0 cm) maximum
J.
5" (12.7 cm) minimum distance to nearest left and right
side combustible surface
K.
3" (7.62 cm) minimum distance to rear combustible
surface
L.
Gas line opening - wall: anywhere 5" (12.7 cm) below
underside of countertop. Cabinet floor: anywhere within
6" (15.2 cm) of rear wall is recommended
M.
24
13
/
16
" (63.0 cm) minimum countertop depth is required
NOTE:
After making the countertop cutout, some installations
may require notching down the base cabinet side walls to clear
the cooktop base. To avoid this modification, use a base cabinet
with sidewalls wider than the cutout.
If cabinet has a drawer, a 4" (10.2 cm) depth clearance from the
countertop to the top of the drawer (or other obstruction) in base
cabinet is required. The drawer depth may need to be shortened
to avoid interfering with the regulator.
Electrical Requirements
General Information
This appliance must be supplied with the proper voltage and
frequency and connected to an individual, properly grounded
branch circuit, protected by a circuit breaker or fuse having
amperage as noted on the rating plate. We recommend you have
the electrical wiring and hookup of your cooktop connected by a
qualified electrician.
After installation, have the electrician show you where your main
cooktop disconnect is located. Check with your local utilities for
electrical codes which apply in your area. Failure to wire your
cooktop according to governing codes could result in a hazardous
condition.
If there are no codes, your cooktop must be wired and fused to
meet the requirements of the National Electrical Code,
ANSI/NFPA No. 70 - Latest edition.
You can get a copy by writing:
National Fire Protection Association
Battery march Park
Quincy. MA 02269
In Canada your cooktop must be wired and fused to meet the
requirements of the Canadian Electrical Code, CSA C22.1-02.
Be sure the installation of this product in a mobile home conforms
with the Manufactured Home Construction and Safety Standard,
Title 24 CFR, Part 3280.
If this standard does not apply, you must follow the standard for
Manufactured Home Installations, ANSI A225.1 and
Manufactured Home Installations, Sites and Communities and
ANSI/NFPA 501A or with local codes.
You can get a copy of the Federal Standard by Writing:
Office of Mobile Home Standard HUD Building
451 7th Street, S. W.
Washington, D.C. 24010
Electrical Connection
An adequate electrical supply and outlet must be used to operate
the electrical parts of your cooktop.
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
IMPORTANT:
For personal safety, this appliance must be properly
grounded.
Содержание JGCK424PS
Страница 31: ...NOTES...
